Rating:
Information o-ring Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$10.00
21 May 2022
US: EFI Equipment and Pa
O-RING FOR ALLIS-CHALMERS: 096049-0300
Parts Express ALLIS-CHALMERS || All Brand new & rebuilt items comes with 1 year warranty. || O-RING. Category: ALLIS-CHALMERS FORKLIFT PARTS. This part can also be found under the following part numbers: ACND096049-0300 096049-0300 ALLIS CHALMERS/TUSK AC ND096049-0300 ALLIS CHALMERS/TUSKND096049-0300 ACND0960490300 AC ND0960490300 ND096049-0300 ALLIS CHALMERS/TUSK ND0960490300 ALLIS CHALMERS/TUSKND0960490300 ND0960490300. All Brand new & rebuilt items comes with 1 year warranty.
Parts Express ALLIS-CHALMERS || All Brand new & rebuilt items comes with 1 year warranty. || O-RING. Category: ALLIS-CHALMERS FORKLIFT PARTS. This part can also be found under the following part numbers: ACND096049-0300 096049-0300 ALLIS CHALMERS/TUSK AC ND096049-0300 ALLIS CHALMERS/TUSKND096049-0300 ACND0960490300 AC ND0960490300 ND096049-0300 ALLIS CHALMERS/TUSK ND0960490300 ALLIS CHALMERS/TUSKND0960490300 ND0960490300. All Brand new & rebuilt items comes with 1 year warranty.
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09604-90300
22193-5477
O-RING
0960490300
22193-54770
TOYOTA
O-RING
0960490300
22193-54770
TOYOTA
O-RING
0960490300
8-97141190-0
ISUZU
O-RING
0960490300
ME736378
MITSUBISHI
O-RING
0960490300
90099-14048
TOYOTA
O-RING
0960490300
S501 24 171
MAZDA
O-RING
Information:
The following charts give general torques for bolts, nuts and taperlock studs of SAE Grade 5 or better quality.
Torques For Bolts And Nuts With Standard Threads
Torques For Taperlock Studs
Use these standard torque values for all fasteners unless otherwise specified in this publication or in the Service Manual.Torque For Metric Fasteners
Be very careful never to mix metric with customary (standard) fasteners. Mismatched or incorrect fasteners will cause engine damage or malfunction and may even result in personal injury. Original fasteners removed from the engine should be saved for reassembly whenever possible. If new fasteners are needed, they must be of the same size and grade as the ones that are being replaced.The material strength identification is usually shown on the bolt head by numbers (8.8, 10.9, etc.). The following chart gives general torques for bolts and nuts with Grade 8.8.
Torque For Standard Hose Clamps-Worm Drive Band Type
The following chart gives the torques for initial installation of those clamps on new hose and for reassembly or tightening of hose clamps on existing hose.
Constant Torque Hose Clamps
A constant torque hose clamp can be used in place of any standard hose clamp. Make sure the constant torque hose clamp is the same size as the standard clamp.Due to extreme temperature changes, hose will heat set. Heat setting causes hose clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures caused by hose clamps loosening. The new, constant torque hose clamp will help prevent these failures.Installation
Each installation application can be different depending on the type of hose, fitting material and anticipated expansion or contraction of the hose and fittings. A torque wrench should be used for proper installation of the new, constant torque hose clamps. Constant torque hose clamps should be installed as follows: To allow for maximum expansion, install clamps at 50 lb in (5.7 N m).To allow for equal expansion and contraction, install clamps at 90 lb in (10.2 N m).To allow for maximum contraction, install clamps at 125 lb in (14.1 N m).