Rating:
Information nozzle assy Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Injector nozzle 12 Pieces DN4PD1 093400-5010 DN4PD57 093400-5640 DN4PD681 093400-6810 diesel nozzle - (Color: 093400-5640)
Generic Color: 093400-5640
Generic Color: 093400-5640
Injector nozzle 12 Pieces DN4PD1 093400-5010 DN4PD57 093400-5640 DN4PD681 093400-6810 diesel nozzle - (Color: 093400-5010)
Generic Color: 093400-5010
Generic Color: 093400-5010
$21.45
03 Dec 2021
CN: EMIAOTO
EMIAOTO 1PCS Diesel Injector Nozzle for DN4PD57/093400-5571/105007-1260 093400-5640/9 432 610 284/23 620 59045
EMIAOTO OEM Part Numbers : DN4PD57/093400-5571/105007-1260 093400-5640 / 9 432 610 284 / 23 620 59045 || Fit for: || Conditions: new and high quality. The product is the same size as the original part, and the replacement is simple. || One year warranty, shipped within 1-2 days and delivered to you within 10-20 days || We refund or reship for non-received items that is over our estimate shipping time for free
EMIAOTO OEM Part Numbers : DN4PD57/093400-5571/105007-1260 093400-5640 / 9 432 610 284 / 23 620 59045 || Fit for: || Conditions: new and high quality. The product is the same size as the original part, and the replacement is simple. || One year warranty, shipped within 1-2 days and delivered to you within 10-20 days || We refund or reship for non-received items that is over our estimate shipping time for free
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09340-05640
NOZZLE ASSY
Information:
If there is clearance available, it is recommended that the oil pan be removed prior to removing the rear seal carrier. A new oil pan gasket must be installed after the rear seal carrier has been installed.1. Loosen oil pan mounting bolts (2). Carefully lower the oil pan away from the cylinder block.2. Remove eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block. Using a screwdriver, carefully pry the rear seal carrier off of the two dowels in the cylinder block. The following steps are for the installation of the rear seal carrier.
1U8846 Gasket Maker is used on the joint face of the rear seal carrier. Do not allow the gasket maker to get into the oil passage in the cylinder block mounting face.
3. Prepare rear seal carrier (3) for installation as follows: a. Clean the joint face of the rear seal carrier with 8T9011 Component Cleaner.b. Apply 6V1541 Quick Cure Primer to the joint face of the rear seal carrier. Allow the primer to air dry three to five minutes.c. Apply 1U8846 Gasket Maker to the joint face of the rear seal carrier. Spread the gasket maker uniformly. The rear seal carrier must be installed within ten minutes after application of the gasket maker.4. Put rear seal carrier (3) in position on the dowels in the rear of the cylinder block. If necessary, use a soft faced hammer to position the rear seal carrier against the cylinder block.5. Apply 9S3263 Thread Lock on the threads of eight bolts (1). Install eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block.6. Check the condition of the oil pan gasket. If the gasket is not damaged, raise the oil pan into position, and tighten oil pan mounting bolts (2). If the gasket is damaged, remove the oil pan, and replace the gasket. See the topic "Remove & Install Oil Pan" in this module.End By:a. install flywheel housing
1U8846 Gasket Maker is used on the joint face of the rear seal carrier. Do not allow the gasket maker to get into the oil passage in the cylinder block mounting face.
3. Prepare rear seal carrier (3) for installation as follows: a. Clean the joint face of the rear seal carrier with 8T9011 Component Cleaner.b. Apply 6V1541 Quick Cure Primer to the joint face of the rear seal carrier. Allow the primer to air dry three to five minutes.c. Apply 1U8846 Gasket Maker to the joint face of the rear seal carrier. Spread the gasket maker uniformly. The rear seal carrier must be installed within ten minutes after application of the gasket maker.4. Put rear seal carrier (3) in position on the dowels in the rear of the cylinder block. If necessary, use a soft faced hammer to position the rear seal carrier against the cylinder block.5. Apply 9S3263 Thread Lock on the threads of eight bolts (1). Install eight bolts (1) and the washers that hold the rear seal carrier to the cylinder block.6. Check the condition of the oil pan gasket. If the gasket is not damaged, raise the oil pan into position, and tighten oil pan mounting bolts (2). If the gasket is damaged, remove the oil pan, and replace the gasket. See the topic "Remove & Install Oil Pan" in this module.End By:a. install flywheel housing