Rating:
Information nozzle assy Denso
Nozzle Type:
ND-DN0PD37
MITSUBISHI LANCER/MIRAGE 4D68
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$46.89
22 Dec 2023
KR: Adabus
093400-5010 093400-5040 093400-5060 093400-5200 093400-5210 093400-5310 093400-5320 093400-5370 diesel fuel injector with DN4PD1 - (Color: 093400-5040)
Generic Color: 093400-5040 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
Generic Color: 093400-5040 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
$46.89
27 Nov 2023
KR: Adabus
093400-5010 093400-5040 093400-5060 093400-5200 093400-5210 093400-5310 093400-5320 093400-5370 diesel fuel injector with DN4PD1 - (Color: 093400-5200)
Generic Color: 093400-5200 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
Generic Color: 093400-5200 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
$46.89
06 Mar 2024
KR: Adabus
093400-5010 093400-5040 093400-5060 093400-5200 093400-5210 093400-5310 093400-5320 093400-5370 diesel fuel injector with DN4PD1 - (Color: 093400-5320)
Generic Color: 093400-5320 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
Generic Color: 093400-5320 || Other part number: Fuel Pump Regulator || Placement on vehicle: Engine oil pump || Country/region of manufacture: HK || Special features: The oxide layer
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09340-05370
MD620116
NOZZLE ASSY
0934005370
MD620116
MITSUBISHI
NOZZLE ASSY
Information:
1. Loosen two bolts (2) and two nuts (3). Remove bolt (1), and remove fan drive belts (4).2. Remove the nuts and bolts that hold the fan drive in place. Remove fan drive (5). The following steps are for installation of the fan drive.3. Put fan drive (5) in position on the timing gear cover.4. Install bolts (2) and nuts (3) loosely. Make a replacement of the belts as a set only.5. Install fan belts (4). Install bolt (1). Make an adjustment to the belt tension with tool (A). Measure the belt farthest away from the engine. Tighten new belts to a gauge indication of 120 5. After the engine is operated at high idle for a minimum of 30 minutes, make another adjustment to the belt tension. The correct tension for used belts is a gauge indication of 90 10.6. Tighten bolts (2) and nuts (3) that hold the fan drive in place.Disassemble Fan Drive
Start By:a. remove fan drive This is a typical later model fan drive. 1. Remove two bolts (2) that hold the fan adapter to the pulley.2. Remove fan adapter (1) from the pulley 3. Remove bolts (3) and washer (4). Remove seal (5). 4. Remove pulley (8) from bracket (6).5. Remove bearing (10) and spacer (9) from the pulley. Remove spacer (7), seal (11) and bearing (12) from the pulley.Assemble Fan Drive
1. Install bearing (12) in the rear of pulley (8). 2. Install lip-type seal (11) with tooling (A). The lip of the seal must be away from the bearing. Put 5P960 Multipurpose Grease on the lip of the seal.3. Install spacer (7) so the end with the taper is toward the inside of pulley (8).4. Install spacer (9) and bearing (4) in the front of the pulley. 5. Put seal (5) on the front of the pulley. Install the pulley on bracket (6). 6. Install washer (4) and bolts (3) that hold the pulley in position.7. Install the fan drive adapter on the pulley.8. Fill the fan drive with 5P960 Multipurpose Grease.End By:a. install fan drive
Start By:a. remove fan drive This is a typical later model fan drive. 1. Remove two bolts (2) that hold the fan adapter to the pulley.2. Remove fan adapter (1) from the pulley 3. Remove bolts (3) and washer (4). Remove seal (5). 4. Remove pulley (8) from bracket (6).5. Remove bearing (10) and spacer (9) from the pulley. Remove spacer (7), seal (11) and bearing (12) from the pulley.Assemble Fan Drive
1. Install bearing (12) in the rear of pulley (8). 2. Install lip-type seal (11) with tooling (A). The lip of the seal must be away from the bearing. Put 5P960 Multipurpose Grease on the lip of the seal.3. Install spacer (7) so the end with the taper is toward the inside of pulley (8).4. Install spacer (9) and bearing (4) in the front of the pulley. 5. Put seal (5) on the front of the pulley. Install the pulley on bracket (6). 6. Install washer (4) and bolts (3) that hold the pulley in position.7. Install the fan drive adapter on the pulley.8. Fill the fan drive with 5P960 Multipurpose Grease.End By:a. install fan drive