Rating:
Information nozzle assy Denso
ZEXEL
105000-1740
INJECTION NOZZLE
NP-DN0SD193
105000-1740
BOSCH
0434250063
INJECTION NOZZLE
DN0SD193
0434250063
CAV
INJECTION NOZZLE
BDN0SD193
Nozzle Type:
ND-DN0SD193
MAZDA INDUSTRIAL P865
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4 pieces DN0SD193 fuel diesel injection nozzle 093400-1310 DN0SD193 DNOSD193 0434250063
MAEDHWB Ideal Replacement: Made with materials and precision-designed, suitable for specific vehicles, helping to improve power and smooth operation. || KEY FUNCTION: The primary function of a fuel injector is to deliver precise amounts of fuel into the engine's combustion chamber at the appropriate time. It atomizes the fuel into a fine mist and sprays it directly into the intake manifold or cylinder, ensuring efficient mixing with incoming air for combustion. || QUALITY CONTROL: Stringent quality control measures are implemented throughout the manufacturing process to ensure the reliability and performance of the fuel injectors. This includes inspections, functional tests, and flow rate measurements to maintain consistent quality standards. || NOTE: Please make sure that the model number, part number and photo is the same as yours. To Avoid placing wrong orders and wasting your precious time. The Injector calibration codes are located on the top of the product as shown in Picture. Professional installation is highly recommend.
MAEDHWB Ideal Replacement: Made with materials and precision-designed, suitable for specific vehicles, helping to improve power and smooth operation. || KEY FUNCTION: The primary function of a fuel injector is to deliver precise amounts of fuel into the engine's combustion chamber at the appropriate time. It atomizes the fuel into a fine mist and sprays it directly into the intake manifold or cylinder, ensuring efficient mixing with incoming air for combustion. || QUALITY CONTROL: Stringent quality control measures are implemented throughout the manufacturing process to ensure the reliability and performance of the fuel injectors. This includes inspections, functional tests, and flow rate measurements to maintain consistent quality standards. || NOTE: Please make sure that the model number, part number and photo is the same as yours. To Avoid placing wrong orders and wasting your precious time. The Injector calibration codes are located on the top of the product as shown in Picture. Professional installation is highly recommend.
$18.03
26 Oct 2024
KR: Adabus
Diesel Nozzle 093400-1310 DN0SD193 DNOSD193 0434250063
Generic
Generic
$51.50
17 Oct 2024
KR: Adabus
4 Pcs R2 RF Injector Nozzle DN0SD193 093400-1310 forMazda Bongo 626 Mk Capella II III B-Serie 323 ASTINA Familia 2.0 2.2
Generic For Mazda BONGO Bus (SR1) E2200 D 4WD R2 2184cc 1984/01-1988/02 || For Mazda BONGO Bus (SR1) E2200 D R207 2169cc 1984/01-1988/02 || For Mazda ETUDE V (BA) 2.0 D RF1G 1998cc 1996/10-1998/09 || For Mazda 626 Mk II (GC) 2.0 D RF46 1998cc 1982/11-1987/06 || For Mazda 626 III Station Wagon (GV) 2.0 D RF-CX/RF-N/RFG5 1998cc1988/09-1997/09
Generic For Mazda BONGO Bus (SR1) E2200 D 4WD R2 2184cc 1984/01-1988/02 || For Mazda BONGO Bus (SR1) E2200 D R207 2169cc 1984/01-1988/02 || For Mazda ETUDE V (BA) 2.0 D RF1G 1998cc 1996/10-1998/09 || For Mazda 626 Mk II (GC) 2.0 D RF46 1998cc 1982/11-1987/06 || For Mazda 626 III Station Wagon (GV) 2.0 D RF-CX/RF-N/RFG5 1998cc1988/09-1997/09
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09340-01310
NOZZLE ASSY
Information:
* Inspect the radiator for leaks and trash build-up. * Inspect the radiator hoses for cracks and loose clamps.* Inspect the fan and accessory drive belts for cracks, breaks or other damage. Belts for multiple groove pulleys are sold in matched sets. Belts for multiple groove pulleys must be replaced as matched sets. If only one belt of a two or three belt set is replaced, it will carry more of a load than the belts not replaced since the older belts are stretched. The additional load on the new belt could cause it to break. * Inspect the water pump for leaks. The water pump seal is lubricated by coolant in the cooling system. It is normal for a small amount of leakage to occur as the engine cools down and parts contract. * Inspect the engine for oil leaks, such as front and rear crankshaft seals, crankcase, oil filter and valve covers.* Inspect the fuel system for leaks, loose fuel line clamps and fittings and loose or worn hoses. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more frequently than the recommended service intervals prescribed in this publication until a leak is found or fixed, or until the suspicion for a leak has been proven to be unwarranted. * Inspect wiring for loose connections and worn or frayed wires.* Inspect air intake system hoses and elbows for cracks and loose clamps.* Inspect engine-to-frame ground strap for good connection and condition.Pre-Start Checks
* Measure the engine crankcase oil level. The correct oil level is shown by the marks between the words "ADD" and "FULL RANGE" on the dipstick (oil level gauge) on the "Engine Stopped" side.The location of the ADD and FULL RANGE marks on the engine dipstick are determined by the tilt angle of the engine after it is installed in the truck.If the ADD and FULL RANGE marks have not been stamped on the dipstick, see "Calibration" in the "Dipsticks" section of this manual or contact your authorized Caterpillar dealer. * Check the coolant level with the engine stopped and cold. Remove the filler cap slowly to relieve pressure.* Maintain the coolant level to within 1/2 inch (13 mm) of the bottom of the fill pipe. Install the filler cap.* If equipped with a sight glass, maintain the coolant to the proper level.
To prevent engine damage, never add coolant to an overheated engine. Allow the engine to cool first.
Typical Example* Observe the air cleaner service indicator (if equipped). Service the air cleaner when the yellow diaphragm enters the red zone or the red piston locks in the visible position. If your truck air cleaner is not equipped with an indicator, your authorized Caterpillar dealer can provide one for you.* Check fuel level. Do not fill fuel tank to top. Fuel expands as it gets warm and may overflow.
* Measure the engine crankcase oil level. The correct oil level is shown by the marks between the words "ADD" and "FULL RANGE" on the dipstick (oil level gauge) on the "Engine Stopped" side.The location of the ADD and FULL RANGE marks on the engine dipstick are determined by the tilt angle of the engine after it is installed in the truck.If the ADD and FULL RANGE marks have not been stamped on the dipstick, see "Calibration" in the "Dipsticks" section of this manual or contact your authorized Caterpillar dealer. * Check the coolant level with the engine stopped and cold. Remove the filler cap slowly to relieve pressure.* Maintain the coolant level to within 1/2 inch (13 mm) of the bottom of the fill pipe. Install the filler cap.* If equipped with a sight glass, maintain the coolant to the proper level.
To prevent engine damage, never add coolant to an overheated engine. Allow the engine to cool first.
Typical Example* Observe the air cleaner service indicator (if equipped). Service the air cleaner when the yellow diaphragm enters the red zone or the red piston locks in the visible position. If your truck air cleaner is not equipped with an indicator, your authorized Caterpillar dealer can provide one for you.* Check fuel level. Do not fill fuel tank to top. Fuel expands as it gets warm and may overflow.