Rating:
Information holder & nozzle se Denso
Product
Nozzle & Nozzle Holder
Vehicle engine
INDUSTRIAL S4S-DT
Engine
S4S-DT
Serial start-end
0601-
Info
Injector Nozzle
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4X Fuel Injector 093500-7730 0935007730 093500-8010 0935008010 for Denso
Ranntwdsu Part number:093500-7730 || Application:for Denso
Ranntwdsu Part number:093500-7730 || Application:for Denso
$148.99
16 Aug 2024
CN: PYBCPDM
Pmtihxu 4 PCS Fuel Injector 093500-7730 093500-8010 Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B 0935007730 0935008010
Pmtihxu Item Type: 093500-7730 Fuel Injector || Part number: 093500-7730 093500-8010 || Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B || Condition: New || Note: 1.We Only Ship To Confirmed Order Addresses. Your Order Address Must Match Your Shipping Address. 2.in Order To Avoid Unnecessary Return,please Check The Product Picture And Part Number Carefully To Make Sure It Is The Product You Want.
Pmtihxu Item Type: 093500-7730 Fuel Injector || Part number: 093500-7730 093500-8010 || Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B || Condition: New || Note: 1.We Only Ship To Confirmed Order Addresses. Your Order Address Must Match Your Shipping Address. 2.in Order To Avoid Unnecessary Return,please Check The Product Picture And Part Number Carefully To Make Sure It Is The Product You Want.
$50.99
16 Aug 2024
CN: PYBCPDM
Pmtihxu Fuel Injector 093500-7730 093500-8010 Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B 0935007730 0935008010
Pmtihxu Item Type: 093500-7730 Fuel Injector || Part number: 093500-7730 093500-8010 || Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B || Condition: New || Note: 1.We Only Ship To Confirmed Order Addresses. Your Order Address Must Match Your Shipping Address. 2.in Order To Avoid Unnecessary Return,please Check The Product Picture And Part Number Carefully To Make Sure It Is The Product You Want.
Pmtihxu Item Type: 093500-7730 Fuel Injector || Part number: 093500-7730 093500-8010 || Fits For Mitsubishi S4S S4S S6S 3044C C3.4 3046 Engine Loader 236B || Condition: New || Note: 1.We Only Ship To Confirmed Order Addresses. Your Order Address Must Match Your Shipping Address. 2.in Order To Avoid Unnecessary Return,please Check The Product Picture And Part Number Carefully To Make Sure It Is The Product You Want.
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-08010
HOLDER & NOZZLE SE
Include in ##:
09350-08010
as HOLDER & NOZZLE SE
Nozzle Specification:
Parts number
0935008010 MITSUBISHI
Nozzle
0934009180
First opm
17.65
First op
179.98
Second om
-
Second op
-
Torquen
39.2-49.0
Torque
4.0-5.0
Prelift
-
Max lift
0.23-0.28
Engine
INDUSTRIAL S4S-DT
Information
Include as Nozzle:
Cross reference number
Part num
Firm num
Firm
Name
09350-08010
HOLDER & NOZZLE SE
Information:
Disassembly of Fuel Injection Nozzles
Inspection of Fuel Injection Nozzles
Check each fuel injection nozzle for the following, and if defects are found, repair or replace the fuel injection nozzle.(1) Inspection of injection start pressure(a) Install each fuel injection nozzle on the nozzle tester, and move the handle up and down to release air.(b) Operate the handle of the tester at a rate of about 1 stroke per second, and read the indication on the pressure gage. The indication rises slowly, and the indicator oscillates during spraying. To obtain the injection start pressure value, read the indication when the indicator starts to oscillate.
Inspection of fuel injection nozzle valve opening(c) If the injection start pressure deviates significantly from the standard value, disassemble the fuel injection nozzle, and make an adjustment by changing the washer thickness. 0.1 mm [0.0039 in.] thickness of shims will change the injection pressure 0.98 Mpa (10 kgf/cm2 [142 psi]. The shims are available in 10 different thickness from 1.25 to 1.70 mm [0.0492 to 0.0669 in.] increment of 0.05 mm [0.0020 in.]
Never tap the tip of the nozzle tip when removing the nozzle tip.
Replacement of fuel injection nozzle tip(2) Inspection of fuel injection nozzle spray pattern(a) When inspecting each fuel injection nozzle with the nozzle tester, also check the nozzle for clogs, spray pattern and leakage.(b) Make sure that the fuel is sprayed straight from the nozzle when the handle of the tester is operated at a rate of about 1 stroke per second.
Inspection of spray pattern of fuel injection nozzle(3) Cleaning and replacement of faulty nozzles(a) Loosen the nozzle retaining nut, remove the nozzle tip, and clean the needle valve and body.
Never tap the tip of the nozzle tip when removing the nozzle tip.
(b) Use a fresh cleaning solution to clean the needle valve and body. After cleaning, assemble the needle valve and body in clean diesel fuel. The needle valve and body are precision finished. Handle them carefully, and do not change the combination of parts.
Cleaning of fuel injection nozzle tip(c) Tighten the nozzle retaining nut on the nozzle tip to the specified torque.(d) If the spray pattern is still not acceptable after adjustment and cleaning, replace the nozzle tip. (a) Never touch the sliding surface of the needle valve.(b) When installing a new nozzle tip, remove the seal film (synthetic resin film), and slide needle valve in the nozzle in a fresh cleaning solution to remove anti-rust oil coating thoroughly from the new nozzleReassembly of Fuel Injection Nozzles
Fuel Filter
Disassembly and Inspection of Fuel Filter
Inspection of Fuel Injection Nozzles
Check each fuel injection nozzle for the following, and if defects are found, repair or replace the fuel injection nozzle.(1) Inspection of injection start pressure(a) Install each fuel injection nozzle on the nozzle tester, and move the handle up and down to release air.(b) Operate the handle of the tester at a rate of about 1 stroke per second, and read the indication on the pressure gage. The indication rises slowly, and the indicator oscillates during spraying. To obtain the injection start pressure value, read the indication when the indicator starts to oscillate.
Inspection of fuel injection nozzle valve opening(c) If the injection start pressure deviates significantly from the standard value, disassemble the fuel injection nozzle, and make an adjustment by changing the washer thickness. 0.1 mm [0.0039 in.] thickness of shims will change the injection pressure 0.98 Mpa (10 kgf/cm2 [142 psi]. The shims are available in 10 different thickness from 1.25 to 1.70 mm [0.0492 to 0.0669 in.] increment of 0.05 mm [0.0020 in.]
Never tap the tip of the nozzle tip when removing the nozzle tip.
Replacement of fuel injection nozzle tip(2) Inspection of fuel injection nozzle spray pattern(a) When inspecting each fuel injection nozzle with the nozzle tester, also check the nozzle for clogs, spray pattern and leakage.(b) Make sure that the fuel is sprayed straight from the nozzle when the handle of the tester is operated at a rate of about 1 stroke per second.
Inspection of spray pattern of fuel injection nozzle(3) Cleaning and replacement of faulty nozzles(a) Loosen the nozzle retaining nut, remove the nozzle tip, and clean the needle valve and body.
Never tap the tip of the nozzle tip when removing the nozzle tip.
(b) Use a fresh cleaning solution to clean the needle valve and body. After cleaning, assemble the needle valve and body in clean diesel fuel. The needle valve and body are precision finished. Handle them carefully, and do not change the combination of parts.
Cleaning of fuel injection nozzle tip(c) Tighten the nozzle retaining nut on the nozzle tip to the specified torque.(d) If the spray pattern is still not acceptable after adjustment and cleaning, replace the nozzle tip. (a) Never touch the sliding surface of the needle valve.(b) When installing a new nozzle tip, remove the seal film (synthetic resin film), and slide needle valve in the nozzle in a fresh cleaning solution to remove anti-rust oil coating thoroughly from the new nozzleReassembly of Fuel Injection Nozzles
Fuel Filter
Disassembly and Inspection of Fuel Filter