Rating:
Information holder & nozzle se Denso
Product
Nozzle & Nozzle Holder
Vehicle engine
LAND CRUISER 1HZ
Engine
1HZ
Serial start-end
9712-
Info
Injector Nozzle
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
6X Fuel Injector 093500-6890 0935006890 Compatible for 1HZ Engine
Wieoncke 【Part Name】:Fuel Injector || 【Part Number】:093500-6890 0935006890 || 【Application】:Compatible for 1HZ Engine || 【Notice】-Application information provided is for reference only. Please confirm the part number and compare old parts before purchase. If you have any question,pls feel free to ask us. || 【Worth Choice】-This product has stable performance, high reliability, easy installation and fast response.y to you as soon as possible.
Wieoncke 【Part Name】:Fuel Injector || 【Part Number】:093500-6890 0935006890 || 【Application】:Compatible for 1HZ Engine || 【Notice】-Application information provided is for reference only. Please confirm the part number and compare old parts before purchase. If you have any question,pls feel free to ask us. || 【Worth Choice】-This product has stable performance, high reliability, easy installation and fast response.y to you as soon as possible.
6X Fuel Injector 093500-6890 0935006890 Compatible with 1HZ Engine
DJCXYSM Product Name:Fuel Injector || Part number:093500-6890 0935006890 || Application:Compatible with 1HZ Engine || NOTE: To avoid unnecessary returns, please check the part number before purchasing, or tell us the picture of your engine model and nameplate to reduce the error rate. thank you. || Tip: If you have any questions before or after sale, please contact us in time. We'll help you out as soon as possible. Thank you
DJCXYSM Product Name:Fuel Injector || Part number:093500-6890 0935006890 || Application:Compatible with 1HZ Engine || NOTE: To avoid unnecessary returns, please check the part number before purchasing, or tell us the picture of your engine model and nameplate to reduce the error rate. thank you. || Tip: If you have any questions before or after sale, please contact us in time. We'll help you out as soon as possible. Thank you
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-06890
HOLDER & NOZZLE SE
Include in ##:
Nozzle Specification:
Parts number
0935006890 TOYOTA
Nozzle
0934006280
First opm
14.70-15.68
First op
150-160
Second om
Second op
Torquen
44.1-49.0
Torque
4.5-5.0
Prelift
-
Max lift
Engine
LAND CRUISER 1HZ
Information
Include as Nozzle:
Cross reference number
Part num
Firm num
Firm
Name
09350-06890
HOLDER & NOZZLE SE
Information:
Removing:
6-1Cut through the starter gear ring with a hard chisel and remove.Fig. 6-1Refitting:
1. Heat the starter gear ring to a temperature of 120 deg. C. Place the starter gear ring with the bevelled side of the teeth facing away from flywheel.
6-22. Locate the starter gear ring on the flywheel and tap it into position so that it seats against the shoulder.Fig. 6-2Removing And Fitting A Radial Sealing Ring On The Flywheel Side
It is assumed that the flywheel has been dismantled. Removing:
6-3Apply puller No. 142700 and draw off radial sealing ring.Fig. 6-3Refitting:
6-41. Mount guide-piece of device onto crankshaft.Fig. 6-4
6-52. Lightly grease the sealing lip of the new radial seal. Place seal on guide-piece with lip facing towards crankcase and press in with device No. 142530.Fig. 6-5 Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the complete cover by adding gaskets accordingly.Dismantling, Installing And Sealing The Cover On The Flywheel Side (As from 3-cylinder engine)
The flywheel has already been removed.Dismantling:
1. Remove the bolts in the oil sump securing the cover on the flywheel side and the bolts securing the cover to the crankcase. Remove cover and gasket. Renew radial sealing ring. Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the latter in the cover.Installing:
6-112. Adhere new gasket to crankcase. Trim off the portion of gasket projecting beyond the joint surface of the sump. Fig. 6-113. Apply coat of Deutz DW 48 jointing compound to the oil sump gasket in the region of the cover.
6-124. Press new radial seal into the rear cover so that the outside surface is flush (arrow).Fig. 6-12 Prior to fitting, heat cover "hand-warm" and coat radial seal with jointing compound.
6-135. Place cover in position. Lightly pretighten cover bolts in crankcase. Fully tighten sump bolts in cover, then fully tighten bolts in crankcase.Fig. 6-13Exploded Views
6-1Cut through the starter gear ring with a hard chisel and remove.Fig. 6-1Refitting:
1. Heat the starter gear ring to a temperature of 120 deg. C. Place the starter gear ring with the bevelled side of the teeth facing away from flywheel.
6-22. Locate the starter gear ring on the flywheel and tap it into position so that it seats against the shoulder.Fig. 6-2Removing And Fitting A Radial Sealing Ring On The Flywheel Side
It is assumed that the flywheel has been dismantled. Removing:
6-3Apply puller No. 142700 and draw off radial sealing ring.Fig. 6-3Refitting:
6-41. Mount guide-piece of device onto crankshaft.Fig. 6-4
6-52. Lightly grease the sealing lip of the new radial seal. Place seal on guide-piece with lip facing towards crankcase and press in with device No. 142530.Fig. 6-5 Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the complete cover by adding gaskets accordingly.Dismantling, Installing And Sealing The Cover On The Flywheel Side (As from 3-cylinder engine)
The flywheel has already been removed.Dismantling:
1. Remove the bolts in the oil sump securing the cover on the flywheel side and the bolts securing the cover to the crankcase. Remove cover and gasket. Renew radial sealing ring. Inspect crankshaft in the zone of radial seal contact. If a friction groove has been formed by the radial seal, displace the latter in the cover.Installing:
6-112. Adhere new gasket to crankcase. Trim off the portion of gasket projecting beyond the joint surface of the sump. Fig. 6-113. Apply coat of Deutz DW 48 jointing compound to the oil sump gasket in the region of the cover.
6-124. Press new radial seal into the rear cover so that the outside surface is flush (arrow).Fig. 6-12 Prior to fitting, heat cover "hand-warm" and coat radial seal with jointing compound.
6-135. Place cover in position. Lightly pretighten cover bolts in crankcase. Fully tighten sump bolts in cover, then fully tighten bolts in crankcase.Fig. 6-13Exploded Views