09350-05660 HOLDER & NOZZLE SE Denso Cross


Rating:
26
Buy HOLDER & NOZZLE SE 09350-05660 genuine, new aftermarket engine parts with delivery

Information holder & nozzle se Denso

Product
Nozzle & Nozzle Holder
Vehicle engine
INDUSTRIAL 6D16T2
Engine
6D16T2
Serial start-end
9303-
Info
Injector Nozzle

Components :

00.001
HOLDER & NOZZLE SE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-05660
HOLDER & NOZZLE SE
001
[01]
HOLDER ASSY, NOZZL
001-001
[01]
BODY SUB-ASSY, NOZ
001-002
[01]
PIN, NOZZLE HOLDER
001-003
[01]
SPRING, NOZZLE HOL
001-004
[01]
SCREW, ADJUST
001-005
[01]
NUT, CAP
-0603
001-005
[01]
NUT, CAP
0604-
001-006
[01]
CONNECTOR, NOZZLE
001-007
[01]
GASKET, INLET CONN
001-008
[01]
NUT, NOZZLE RETAIN
001-009
[01]
SCREW, HOLLOW
001-010
[01]
WASHER
001-011
[02]
WASHER, COPPER PLA
T1
002
[01]
NOZZLE ASSY

Include in ##:

09350-05660 as HOLDER & NOZZLE SE

Nozzle Specification:

Parts number
0935005660 MITSUBISHI
Nozzle
0934002330
First opm
22.05-22.83
First op
225-233
Second om
-
Second op
-
Torquen
58.8-78.4
Torque
6.0-8.0
Prelift
-
Max lift
Engine
INDUSTRIAL 6D16T2
Information

Cross reference number



Part num
Firm num
Firm
Name
09350-05660 
 
HOLDER & NOZZLE SE




Information:


Table 1
Required Sleeve Part Numbers
S.No Qty (1) Qty (2) New Part Number Part Name Sleeve color Volume / Injector
1 6 6 449-3816 Locknut Not applicable 0.25 cc (0.02 cubic inch)
2 26 32 420-0939 Spacer Red 0.500 cc (0.030 cubic inch)
3 7 7 420-0940 Spacer Silver 0.75 cc (0.05 cubic inch)
4 0 0 420-0941 Spacer Gold 1.0 cc (0.1 cubic inch)
5 12 12 420-0942 Spacer Green 1.25 cc (0.08 cubic inch)
6 0 0 513-1992 Sleeve Purple (3) 2.5 cc (0.15 cubic inch)
(1) For MD6250 Rotary Drills
(2) For MD6310 Rotary Drills
(3) To be used only on SLV-XL (Jack Casing injectors)
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
General Procedure to Replace Sleeves
Illustration 1 g06357787
(A) Cap
(B) Screw
Remove cap (A) and screw (B). Save the parts.
Illustration 2 g06357788
(C) Sleeve (Silver)
(D) Sleeve (Red)
Remove sleeve (C). Discard the sleeves. Replace sleeve (C) with sleeve (D).
Illustration 3 g06357789
(A) Cap
(B) Screw
Install screw (B) and Cap (A) which were saved in Step 1.Note: Follow the same procedure to replace sleeves in all the grease injectors on the machine.Replace the injector bank sleeve sizes as specified in the instructions below:Grease Injector Location Identification for MD6250 Rotary Drills
The following are the grease injector locations in 503-7710 Requirements for manual or premium lube:Front Left Bank - Lube Points and Locations
Illustration 4 g06355819
Front left bank - lube points
(A) Front Left Jack Casing
(B) Front Left Jack Casing
(C) Front Left Jack Casing
(D) Front Right Jack Casing
(E) Front Right Jack Casing
(F) Front Right Jack Casing
(G) Center Pin on Equalizer Bar
(H) Right Tram Equalizer Pin
(J) Left Tram Equalizer Pin
Table 2
Front Left Bank
Item Description Sleeve color
A Front Left Jack Casing Green
B Front Left Jack Casing Green
C Front Left Jack Casing Green
D Front Right Jack Casing Green
E Front Right Jack Casing Green
F Front Right Jack Casing Green
G Center Pin on Equalizer Bar Silver
H Right Tram Equalizer Pin Silver
J

Have questions with 09350-05660?





Group cross 09350-05660

Back to top