09350-04930 HOLDER & NOZZLE SE Denso Cross


Rating:
13
Buy HOLDER & NOZZLE SE 09350-04930 genuine, new aftermarket engine parts with delivery

Information holder & nozzle se Denso

Product
Nozzle & Nozzle Holder
Vehicle engine
INDUSTRIAL 6D14
Engine
6D14
Serial start-end
9005-
Info
Injector Nozzle

Components :

00.001
HOLDER & NOZZLE SE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-04930
HOLDER & NOZZLE SE
001
[01]
HOLDER ASSY, NOZZL
001-001
[01]
BODY SUB-ASSY, NOZ
001-002
[01]
PIN, NOZZLE HOLDER
001-003
[01]
SPRING, NOZZLE HOL
001-004
[01]
SCREW, ADJUST
001-005
[01]
NUT, CAP
-0603
001-005
[01]
NUT, CAP
0604-
001-006
[01]
CONNECTOR, NOZZLE
001-007
[01]
GASKET, INLET CONN
001-008
[01]
NUT, NOZZLE RETAIN
001-009
[01]
SCREW, HOLLOW
001-010
[01]
WASHER
001-011
[02]
WASHER, COPPER PLA
T1
002
[01]
NOZZLE ASSY

Include in ##:

09350-04930 as HOLDER & NOZZLE SE

Nozzle Specification:

Parts number
0935004930 MITSUBISHI
Nozzle
0934002420
First opm
18.13-18.91
First op
185-193
Second om
-
Second op
-
Torquen
58.8-78.4
Torque
6.0-8.0
Prelift
-
Max lift
Engine
INDUSTRIAL 6D14
Information

Cross reference number



Part num
Firm num
Firm
Name
09350-04930 
 
HOLDER & NOZZLE SE




Information:


When starting the engine with ether, follow these starting procedure instructions carefully. Use ether sparingly and spray it ONLY WHILE CRANKING THE ENGINE. Excessive ether use can cause piston and ring damage. Ether should be used only for cold weather starting.
Table 1
Medium and Heavy-Duty On-Highway Engines (1)
Cold Weather Recommendations    
Starting Aids    
Expected Coldest Temperature     Ether Injection (2)
OR
Air Inlet Heater     Cylinder Block Coolant Heater     Larger Battery
Larger Alternator    
Above
−7 °C (19 °F)     Available     Available     Available    
−7 °C (19 °F) to
−18 °C (0 °F)     Available     Available     Available    
−18 °C (0 °F) to
−28 °C (−18 °F)     Recommended     Required     Recommended    
−28 °C (−18 °F) to
−40 °C (−40 °F)     Recommended     Required     Required    
Less than
−40 °C (−40 °F)     Required     Required     Required    
( 1 ) Options may not be available for all models.
( 2 ) If the engine is equipped with an air inlet heater (AIH) for cold weather starting, do not use types of starting aids such as ether. Such use could result in an explosion and injury.
Table 2
Medium and Heavy-Duty On-Highway Engines (1)
Cold Weather Recommendations    
Improvements for Engine Warm-Up
Improvements for Idle Temperature    
Expected Coldest Temperature     Hand Throttles     Winter Fronts
Shutters     Air Cleaners
Located Under the Hood     On/Off
Fan Drives     BrakeSavers
Exhaust Restrictors    
Above
−7 °C (19 °F)     Available     Available     Available     Available     Available    
−7 °C (19 °F) to
−18 °C (0 °F)     Available     Recommended     Recommended     Recommended     Available    
−18 °C (0 °F) to
−28 °C (−18 °F)     Recommended     Required     Recommended     Required     Recommended    
−28 °C (−18 °F) to
−40 °C (−40 °F)     Required     Required     Recommended     Required     Recommended    
Less than
−40 °C (−40 °F)     Required     Required     Recommended     Required     Required    
( 1 ) Options may not be available for all models.

Have questions with 09350-04930?





Group cross 09350-04930

Back to top