Rating:
Information holder & nozzle se Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$147.00
25 Aug 2021
CN: Jiesheng Auto Parts
Amrxuts 4PCS 23600-54090 Fuel Injector Assy for T-oyota 2L-T 093500-4052
Amrxuts ▶ Fitment - T-oyota 2L-T || ▶The Part Number - 093500-4052 23600-54090 093500-6290 23600-59235 093500-4190 23600-59115 || ▶ CONDITION - When your beloved car has the following failures, please check and replace the fuel injector : Unusual vehicle vibration/ Engine fault light is on/ Difficult to start the car/ Increased fuel consumption || ▶ DIRECT FIT - Easy installation,▶ WARRANTY - Long lifetime and “1 YEAR” warranty .
Amrxuts ▶ Fitment - T-oyota 2L-T || ▶The Part Number - 093500-4052 23600-54090 093500-6290 23600-59235 093500-4190 23600-59115 || ▶ CONDITION - When your beloved car has the following failures, please check and replace the fuel injector : Unusual vehicle vibration/ Engine fault light is on/ Difficult to start the car/ Increased fuel consumption || ▶ DIRECT FIT - Easy installation,▶ WARRANTY - Long lifetime and “1 YEAR” warranty .
$168.00
18 Aug 2020
-: -
YZMZONPARTS 4PCS Fuel Injector Assy 093500-4052 23600-54090 compatible with 2L-T
Replace part number: 093500-4052 23600-54090 093500-6290 23600-59235 093500-4190 23600-59115 || Including: 4PCS Fuel Injector || compatible with 2L-T || New Aftermarket || Warranty: 1 Year
Replace part number: 093500-4052 23600-54090 093500-6290 23600-59235 093500-4190 23600-59115 || Including: 4PCS Fuel Injector || compatible with 2L-T || New Aftermarket || Warranty: 1 Year
You can buy:
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-04052
HOLDER & NOZZLE SE
Include in ##:
Cross reference number
Part num
Firm num
Firm
Name
09350-04052
HOLDER & NOZZLE SE
Information:
Start Bya. remove flywheel
Do not damage the flange on the crankshaft when the crankshaft rear seal is removed. Use of any other tool, other than Tool (A), to remove the crankshaft rear seal, can result in damage to the crankshaft.
1. Carefully make three evenly spaced holes in the crankshaft rear seal with a hammer and sharp punch. Use Tool (A) to remove crankshaft rear seal (1). Do not damage the flange of the crankshaft during seal removal. The following steps are for the installation of the crankshaft rear seal.2. Be sure the flange of the crankshaft is thoroughly clean prior to seal installation. 3. Fasten the 1U7595 Locator Assembly [part of Tool (B)] to the rear of the crankshaft as shown.4. Leaving the seal shipping sleeve in position on the new crankshaft rear seal, position the new seal over the locator assembly. The 1U7597 Sleeve Ring [part of Tool (B)] is not used in this in the seal installation.5. Install the 1U7594 Installer [part of Tool (B)] on the locator assembly. Tighten the nut assembly of Tool (B) to push the crankshaft rear seal into position on the flange of the crankshaft. Remove Tool (B) and the shipping sleeve. The distance between the front face of the crankshaft rear seal and the rear face of the cylinder block must be 15.4 0.5 mm (.61 .02 in) after seal installation. See the topic "Crankshaft Seals" in the 3114 & 3116 Diesel Truck Engines Specifications module, Form No. SENR6436 for further details.End By:a. install flywheel
Do not damage the flange on the crankshaft when the crankshaft rear seal is removed. Use of any other tool, other than Tool (A), to remove the crankshaft rear seal, can result in damage to the crankshaft.
1. Carefully make three evenly spaced holes in the crankshaft rear seal with a hammer and sharp punch. Use Tool (A) to remove crankshaft rear seal (1). Do not damage the flange of the crankshaft during seal removal. The following steps are for the installation of the crankshaft rear seal.2. Be sure the flange of the crankshaft is thoroughly clean prior to seal installation. 3. Fasten the 1U7595 Locator Assembly [part of Tool (B)] to the rear of the crankshaft as shown.4. Leaving the seal shipping sleeve in position on the new crankshaft rear seal, position the new seal over the locator assembly. The 1U7597 Sleeve Ring [part of Tool (B)] is not used in this in the seal installation.5. Install the 1U7594 Installer [part of Tool (B)] on the locator assembly. Tighten the nut assembly of Tool (B) to push the crankshaft rear seal into position on the flange of the crankshaft. Remove Tool (B) and the shipping sleeve. The distance between the front face of the crankshaft rear seal and the rear face of the cylinder block must be 15.4 0.5 mm (.61 .02 in) after seal installation. See the topic "Crankshaft Seals" in the 3114 & 3116 Diesel Truck Engines Specifications module, Form No. SENR6436 for further details.End By:a. install flywheel