Rating:
Information holder & nozzle se Denso
Product
Nozzle & Nozzle Holder
Vehicle engine
MIRAGE/COLT 4D65
Engine
4D65
Serial start-end
8704-
Info
Injector Nozzle
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4X Fuel Injector 093500-3760 0935003760 for Mitsubishi 4D68 4D68AC
TUWODE Part Number: 093500-3760 935003760 || Item Type: Fuel Injector || Applicable Models: Fit for Mitsubishi 4D68 4D68AC || Well-functioning fuel injectors ensure the correct air-fuel ratio, which is essential for minimizing harmful emissions. || Fuel is broken into fine droplets for optimal air mixing and enhanced combustion efficiency.
TUWODE Part Number: 093500-3760 935003760 || Item Type: Fuel Injector || Applicable Models: Fit for Mitsubishi 4D68 4D68AC || Well-functioning fuel injectors ensure the correct air-fuel ratio, which is essential for minimizing harmful emissions. || Fuel is broken into fine droplets for optimal air mixing and enhanced combustion efficiency.
0935003760 093500-3760 4PCS Fuel Injector Mechanism for Mitsubishi Engine 4D68 4D68AC
Podafu Item Type: Fuel Injector || Part Code: 093500-3760 || Applicable Models: Compatible with Mitsubishi Engine 4D68 4D68AC || Provides consistent fuel delivery to ensure smooth engine operation. || Extends the engine's peak performance, thereby improving the vehicle's dependability.
Podafu Item Type: Fuel Injector || Part Code: 093500-3760 || Applicable Models: Compatible with Mitsubishi Engine 4D68 4D68AC || Provides consistent fuel delivery to ensure smooth engine operation. || Extends the engine's peak performance, thereby improving the vehicle's dependability.
BCXFORK 4PCS Fuel Injector 093500-3760 0935003760 for Mitsubishi Engine 4D68 4D68AC
BCXFORK NOTE Before placing an order, please verify that your part number matches the one in the listing. Some Fuel Injectors may look similar. If you're unsure, you can leave us a message and provide a picture of your old fuel injector for verification. || Note: We can provide various engine parts. If you need any additional parts, please leave us a message with the list of items you need. || Manufacturer Warranty 1 Year || Part Number: 093500-3760 0935003760 || This item fits for Mitsubishi Engine 4D68 4D68AC
BCXFORK NOTE Before placing an order, please verify that your part number matches the one in the listing. Some Fuel Injectors may look similar. If you're unsure, you can leave us a message and provide a picture of your old fuel injector for verification. || Note: We can provide various engine parts. If you need any additional parts, please leave us a message with the list of items you need. || Manufacturer Warranty 1 Year || Part Number: 093500-3760 0935003760 || This item fits for Mitsubishi Engine 4D68 4D68AC
You can buy:
$215.99
23 Nov 2023
Components :
Scheme #.#:
№
Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-03760
HOLDER & NOZZLE SE
MD126135
MITSUBISHI
Include in ##:
09350-03760
as HOLDER & NOZZLE SE
Nozzle Specification:
Parts number
0935003760 MITSUBISHI
Nozzle
0934005480
First opm
12.25-13.03
First op
125-133
Second om
-
Second op
-
Torquen
34.3-39.2
Torque
3.5-4.0
Prelift
-
Max lift
Engine
MIRAGE/COLT 4D65
Information
Include as Nozzle:
Cross reference number
Part num
Firm num
Firm
Name
09350-03760
MD126135
HOLDER & NOZZLE SE
0935003760
MD126135
MITSUBISHI
HOLDER & NOZZLE SE
Information:
1. Disconnect water supply hose from water pump inlet.2. Remove connector pipe (1), remove two bolts (2) and remove oil fill pipe (3). 3. Remove bolts (4) and (5) then remove the water pump. The following steps are for the installation of the water pump.4. Position the water pump and install two bolts (4) and (5). Tighten the two bolts evenly.5. Position connector pipe (1) and gaskets then install the bolts.6. Install oil fill pipe (3). Be sure the gasket is in position between the regulator and pipe and install bolts (2).End By:a. Install alternatorb. Fill the cooling system to the specified level. See the Maintenance ManualDisassemble & Assemble Water Pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump
Start By:a. remove water pump 1. Remove three bolts (1) and remove cover (2). 2. Use an M12 X 1.75 bolt to force impeller (3) from shaft (4). Install forcing bolt in impeller as indicated by arrow. Hold impeller and screw bolt in until impeller comes off shaft. 3. Remove bolt (5), washer (6), bearing (7) and gear (8). 4. Remove three bolts (9) and remove cover (10) with bearing (11). 5. Press shaft (4) out of seal (12).
Do not allow shaft (4) to fall to the floor, damage may occur to the shaft.
6. Remove seal (12) and seal (13) from water pump housing. The following steps are for the assembly of the water pump. 7. Using driver group, install seal (13). Refer to illustration to see direction of seal lip. Lubricate shaft seal area with engine oil.8. Assemble shaft (4), bearing (11) and cover (10). Position assembly into seal and housing then install bolts (9). 9. Position the housing and shaft assembly in a press. Position seal (12) on shaft (4). 10. Position tool (A) and press seal into place. 11. Position the water pump in a press, position impeller (3) and press it into place. Dimension X is 1.5 0.5 mm (.059 .020 in).12. Position seal and cover (2), then install bolts (1).End By:a. install water pump