09350-02030 HOLDER & NOZZLE SE Denso Cross


Rating:
73
Buy HOLDER & NOZZLE SE 09350-02030 genuine, new aftermarket engine parts with delivery

Information holder & nozzle se Denso

Product
Nozzle & Nozzle Holder
Vehicle engine
INDUSTRIAL 6PK1
Engine
6PK1
Serial start-end
7911-
Info
Injector Nozzle

Components :

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-02030
HOLDER & NOZZLE SE
001
[01]
HOLDER ASSY, NOZZL
001-001
[01]
BODY
001-002
[01]
PIN, NOZZLE HOLDER
001-003
[01]
SPRING, NOZZLE HOL
001-004
[01]
CONNECTOR SUB-ASSY
001-005
[01]
GASKET, INLET CONN
001-006
[01]
NUT, NOZZLE RETAIN
001-007
[01]
FLANGE
001-008
[01]
SCREW, ADJUST
001-009
[01]
NUT, CAP
001-010
[01]
WASHER
T0.5
001-011
[01]
SCREW, HOLLOW
M8,14.9
001-012
[02]
WASHER, COPPER PLA
T1,ID8.2
002
[01]
NOZZLE ASSY

Include in ##:

09350-02030 as HOLDER & NOZZLE SE

Nozzle Specification:

Parts number
0935002030 MITSUBISHI
Nozzle
0934000200
First opm
13.23-13.72
First op
135-140
Second om
-
Second op
-
Torquen
117.6-127.4
Torque
12.0-13.0
Prelift
-
Max lift
Engine
INDUSTRIAL 6PK1
Information

Include as Nozzle:

0945002000 as Nozzle

Cross reference number



Part num
Firm num
Firm
Name
09350-02030 
 
HOLDER & NOZZLE SE




Information:


Typical Example1. Loosen two bolts (2) and two nuts (3). Remove bolt (1), and remove fan drive belts (4).
Typical Example2. Remove the nuts and bolts that hold the fan drive in place. Remove fan drive (5). The following steps are for installation of the fan drive.3. Put fan drive (5) in position on the timing gear cover.4. Install bolts (2) and nuts (3) loosely. Make a replacement of the belts as a set only.5. Install fan belts (4). Install bolt (1). Make an adjustment to the belt tension with tool (A). Measure the belt farthest away from the engine. Tighten new belts to a gauge indication of 120 5. After the engine is operated at high idle for a minimum of 30 minutes, make another adjustment to the belt tension. The correct tension for used belts is a gauge indication of 90 10.6. Tighten bolts (2) and nuts (3) that hold the fan drive in place.Disassemble Fan Drive
Start By:a. remove fan drive 1. Remove two bolts (2) that hold the fan adapter to the pulley.2. Remove fan adapter (1) from the pulley 3. Remove bolts (3) and washer (4). Remove seal (5). 4. Remove pulley (8) from bracket (6).5. Remove bearing (10) and spacer (9) from the pulley. Remove spacer (7), seal (11) and bearing (12) from the pulley.Assemble Fan Drive
1. Install bearing (12) in the rear of pulley (8). 2. Install lip-type seal (11) with tooling (A). The lip of the seal must be away from the bearing. Put 5P960 Multipurpose Type Grease on the lip of the seal.3. Install spacer (7) so the end with the taper is toward the inside of pulley (8).4. Install spacer (9) and bearing (4) in the front of the pulley. 5. Put seal (5) on the front of the pulley. Install the pulley on bracket (6). 6. Install washer (4) and bolts (3) that hold the pulley in position.7. Install the fan drive adapter on the pulley.8. Fill the fan drive with 5P960 Multipurpose Type Grease.End By:a. install fan drive

Have questions with 09350-02030?





Group cross 09350-02030

Back to top