09350-01610 HOLDER & NOZZLE SE Denso Cross


Rating:
65
Buy HOLDER & NOZZLE SE 09350-01610 genuine, new aftermarket engine parts with delivery

Information holder & nozzle se Denso

Product
Nozzle & Nozzle Holder
Vehicle engine
TRUCK 6D14
Engine
6D14
Serial start-end
7607-
Info
Injector Nozzle

Components :

00.001
HOLDER & NOZZLE SE

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09350-01610
HOLDER & NOZZLE SE
001
[01]
HOLDER ASSY, NOZZL
001-001
[01]
BODY
001-002
[01]
PIN, NOZZLE HOLDER
001-003
[01]
SPRING, NOZZLE HOL
001-004
[01]
SCREW, CAP
001-005
[01]
NUT, CAP
001-006
[01]
CONNECTOR, NOZZLE
001-007
[01]
GASKET, INLET CONN
001-008
[01]
NUT, NOZZLE RETAIN
001-009
[01]
SCREW, HOLLOW
001-010
[01]
GASKET
D26,ID22
001-011
[02]
WASHER, COPPER PLA
T1
002
[01]
NOZZLE ASSY

Include in ##:

09350-01610 as HOLDER & NOZZLE SE

Nozzle Specification:

Parts number
0935001610 MITSUBISHI
Nozzle
0934000711
First opm
21.56
First op
220
Second om
-
Second op
-
Torquen
39.2-49.0
Torque
4.0-5.0
Prelift
-
Max lift
Engine
TRUCK 6D14
Information

Cross reference number



Part num
Firm num
Firm
Name
09350-01610 
 
HOLDER & NOZZLE SE




Information:


View A-A (Rear Face)(6) Bores in block for all camshaft bearings except front bearing ... 69.000 0.038 mm (2.7165 .0015 in)(7) Locate bearing oil hole for all camshaft bearings (except front bearing) at top of bore.
Front Face(8) Bore in block for front camshaft bearing ... 70.000 0.025 mm (2.7559 .0010 in)(9) Front camshaft bearing joint location.(10) Front camshaft bearing oil hole. Install front camshaft bearing with bearing oil hole (10) aligned with oil hole in block and bearing joint (9) positioned as shown.(11) Width of main bearing cap ... 159.995 0.020 mm (6.2990 .0008 in) Width of cylinder block for main bearing cap ... 160.000 0.018 mm (6.2992 .0007 in)(12) Bore in block for main bearings ... 95.000 0.013 mm (3.7402 .0005 in)(13) Main bearing cap bolts. Install as follows: Install bearing caps with sequence number to the right, 1 through 7 (front to rear).a. Before assembly, put 2P2506 Thread Lubricant on the bolt threads and washer face.b. Tighten both bolts of each bearing cap to a torque of ... 54 7 N m (40 5 lb ft)c. Then tighten bolts an additional ... 90 5° (1/4 turn)(14) Location of bearing cap sequence number.(15) Dimension from centerline of crankshaft bore to pan rail ... 110.00 mm (4.331 in)(16) Dimension from centerline of crankshaft bore to top of block ... 322.00 mm (12.677 in)(17) Cylinder bore size ... 105.025 .025 mm (4.1348 .0010 in) Bore size must be checked with a 4C4377 Cylinder Head Stress Plate and gasket installed. Refer to Special Instruction SEHS9047, Installation of 7C6208 Cylinder Sleeve.

Have questions with 09350-01610?





Group cross 09350-01610

Back to top