19080-04011 GOVERNOR ASSY, MEC Denso Cross


Rating:
6
Buy GOVERNOR ASSY, MEC 19080-04011 genuine, new aftermarket engine parts with delivery

Information governor assy, mec Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19080-04011
GOVERNOR ASSY, MEC
RSVH
001
[01]
HOUSING SUB-ASSY,
002
[01]
PLATE
003
[02]
SCREW, ADJUSTING
M8,L57
004
[01]
COVER, GOVERNOR
008
[01]
COLLAR, STEEL
-9901
009
[01]
NUT, CAP
L15.5
010
[01]
SCREW, STROKE ADJU
011
[01]
BUSHING
-9901
011
[01]
BUSHING
9901-
012
[01]
LEVER, TENSION
013
[01]
LEVER SUB-ASSY, CO
014
[01]
PIN, SPLIT
D2,L10
015
[01]
LEVER ASSY, GUIDE
016
[01]
SHAFT, LEVER SUPPO
017
[02]
PLUG, SCREW
019
[01]
E-RING
020
[01]
SHIM
021
[02]
NUT, HEXAGON, W/HO
M6
022
[01]
SLIDER, SUPPORTING
023
[01]
CAPSULE, FULL STOP
-9207
023
[01]
CAPSULE, FULL STOP
9208-
024
[01]
O-RING
ID9.8
025
[01]
NUT, ADAPTER LOCK
026
[01]
SHACKLE ASSY
029
[01]
BEARING, BALL
OD30
031
[01]
FLYWEIGHT ASSY
032
[01]
WASHER, SPRING
T2.5
033
[01]
NUT, ROUND
M12L12.5
034
[01]
SLEEVE, GOVERNOR
035
[4C]
WASHER, PLATE, SK
T0.2
035
[4C]
WASHER, PLATE, SK
T0.3
035
[4C]
WASHER, PLATE, SK
T0.4
035
[4C]
WASHER, PLATE, SK
T0.1
035
[4C]
WASHER, PLATE, SK
T1.0
037
[01]
LEVER ASSY, SWIEVE
038
[02]
BUSHING, LEVER
-9212
038
[02]
BUSHING, LEVER
9212-
039
[02]
O-RING
ID15.8
040
[02]
WASHER, SNAP
ID15
041
[01]
SPRING, SPEED CONT
042
[01]
SPRING, START
043
[01]
ADAPTER ASSY
-9403
043-001
[01]
SCREW, ADPTER
-9403
043-002
[01]
ADAPTER
-9403
043-003
[01]
SPRING, MECHANICAL
-9403
043-004
[01]
E-RING
-9403
043-005
[1C]
WASHER, PLATE, SK
T0.1 -9403
043-005
[1C]
WASHER, PLATE, SK
T0.5 -9403
043-005
[1C]
WASHER, PLATE, SK
T0.2 -9403
043-005
[1C]
WASHER, PLATE, SK
T1.0 -9403
044
[01]
NUT, ADAPTER LOCK
-9403
045
[04]
BOLT, W/WASHER
M6,L40
046
[02]
BOLT, W/WASHER
M6,L50
047
[01]
SEAL, OIL
048
[02]
BOLT, W/WASHER
M6,L16
049
[01]
LEVER, ADJUSTING
050
[01]
LEVER, ADJUSTING
051
[01]
BOLT, W/WASHER
M6,L22
052
[01]
CAP, LEVER
053
[01]
LEVER SUB-ASSY, ST
056
[01]
PLATE, COVER
057
[04]
BOLT, W/WASHER
M6,L14
058
[05]
BOLT, W/WASHER
M6,L14
059
[01]
SCREW,PLUG
060
[01]
WASHER, AIR BLEEDE
T1.6
062
[01]
WASHER, COPPER PLA
T1.5
063
[01]
PACKING, RUBBER PL
064
[01]
SPRING, B
OD3.6
065
[01]
O-RING
ID9.0
066
[01]
BUSHING, BEARING
-9707
066
[01]
BUSHING, BEARING
9707-
067
[01]
COVER, SPRING
068
[01]
SPRING, B
OD6.6
069
[01]
SHAFT, MECHANICAL
070
[01]
CUP, SPRING
071
[01]
LEVER, SUPPORT
072
[01]
SPRING, RETURN
L8.5D1.6
073
[01]
PLATE, CAP
074
[01]
SPRING, B
OD8.6
075
[01]
KEY, WOODRUFF
076
[01]
GASKET, PUMP BODY
-9305
076
[01]
GASKET, PUMP BODY
9305-
077
[01]
GASKET
-9305
077
[01]
GASKET
9306-
078
[01]
WASHER, PLATE
T0.5
079
[01]
E-RING
D5
080
[01]
COMPENSATOR SUB-AS
-9501
080
[01]
COMPENSATOR SUB-AS
9502-
081
[01]
O-RING
ID26.2
082
[01]
PIN
083
[01]
LEVER SUB-ASSY, CO
084
[01]
SPRING, RETURN
086
[01]
BUSHING
087
[1C]
WASHER, PLATE, SK
T0.3
087
[1C]
WASHER, PLATE, SK
T0.6
087
[1C]
WASHER, PLATE, SK
T0.9
088
[01]
NUT, HEXAGON
M8
089
[02]
WASHER, COPPER PLA
T1
090
[01]
O-RING
ID12.3
091
[01]
SCREW, HOLLOW
092
[04]
WASHER, FUEL PIPE
096
[01]
SCREW, HOLLOW
M10,L19
097
[01]
BUSHING
098
[01]
E-RING
099
[01]
NIPPLE, SWIVELING

Include in ##:

09200-00510 as GOVERNOR ASSY, MEC

Cross reference number



Part num
Firm num
Firm
Name
19080-04011 
 
GOVERNOR ASSY, MEC




Information:

Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
When removing a major component or attachment, ensure that it is properly blocked or secured before removing mounting hardware. An assembly that is disconnected without proper blocking may shift or fall, resulting in serious injury or death of personnel or machine damage.
Personal injury or death can result from improper maintenance procedures. To avoid injury or death, follow the procedures exactly as stated below.
Personal injury can result from improper handling of chemicals.Make sure you use all the necessary protective equipment required to do the job.Make sure that you read and understand all directions and hazards described on the labels and material safety data sheet of any chemical that is used.Observe all safety precautions recommended by the chemical manufacturer for handling, storage, and disposal of chemicals.
Do not operate the machine if any guards or covers are missing or inadequately secured. Personnel could be seriously injured or machine damage may occur.
Observe the safe working load limits of all lifting and blocking devices and keep a safe distance from suspended/blocked loads. Personnel may be seriously injured or killed by falling loads.
Reference Section
Refer to Service Magazine, M0082326, "Diesel Exhaust Fluid (DEF) Contamination on C4.4 Machine Engines".Refer to Service Magazine, M0096547, "Diesel Exhaust Fluid (DEF) Pump Filter Maintenance on Certain C4.4 Machine Engines".Refer to Special Instruction, M0096185, "Diesel Exhaust Fluid (DEF) Pump Diesel Contamination Test on Certain C4.4 Engines".Problem
There have been instances of returned DEF pumps that have no fault found or indicating contamination.Resolution
Complete the form below and attach to any SIMSi claim in addition to a Product Status Report (PSR) from before any troubleshooting was performed or any diagnostic codes were cleared.
Use the electronic service tool to download a PSR with Histograms.
Enter the diagnostic codes that require troubleshooting: ___
Perform the correct troubleshooting procedure for any active diagnostic codes. Refer to Troubleshooting, Diagnostic Trouble Codes.
If the troubleshooting procedure requests that the DEF is tested for contamination or concentration , record the results in Table 1 and Table 2.
For other DEF-related troubleshooting procedures, follow the applicable troubleshooting steps and record the results in Table 3.
Table 1
DEF Contamination
Step Instruction Completed Result Units
1 Perform the test procedure for DEF contamination. Refer to Systems Operation, Testing and Adjusting, Diesel Exhaust Fluid Quality - Test.

Have questions with 19080-04011?





Group cross 19080-04011

Back to top