19080-00900 GOVERNOR ASSY, MEC Denso Cross


Rating:
17
Buy GOVERNOR ASSY, MEC 19080-00900 genuine, new aftermarket engine parts with delivery

Information governor assy, mec Denso

KIT List:

Part name
Kit1
Kit2
Governor assy, mec
Governor assy, mec

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19080-00900
GOVERNOR ASSY, MEC
RSV
001
[01]
HOUSING, GOVERNOR
-9311
001
[01]
HOUSING SUB-ASSY,
9312-
002
[01]
PLATE
004
[01]
COVER, GOVERNOR
005
[01]
PIN, STOP
007
[02]
SCREW, ADJUSTING
M8,L57
009
[01]
NUT, CAP
010
[01]
SCREW, STROKE ADJU
011
[01]
BUSHING
012
[01]
LEVER ASSY, TENSIO
-9404
012
[01]
LEVER ASSY, TENSIO
9404-
015
[01]
LEVER ASSY, CONTRO
L/R:2
016
[01]
SHAFT, LEVER SUPPO
017
[02]
PLUG, SCREW
019
[01]
PIN, SPLIT
D2,L10
021
[02]
NUT, HEXAGON, W/HO
023
[01]
SPRING, IDLING
024
[01]
SCREW, ADJUSTING
025
[01]
NUT, HEXAGON
M12
026
[01]
SHACKLE ASSY
029
[01]
BEARING, BALL
OD30
030
[01]
KEY, WOODRUFF
031
[01]
FLYWEIGHT ASSY
032
[01]
WASHER, SPRING
T2.5
033
[01]
NUT, ROUND
034
[01]
SLEEVE, GOVERNOR
035
[C]
WASHER, PLATE, SK
T0.2
035
[C]
WASHER, PLATE, SK
T0.3
035
[C]
WASHER, PLATE, SK
T0.4
035
[C]
WASHER, PLATE, SK
T0.1
035
[C]
WASHER, PLATE, SK
T1.0
037
[01]
LEVER ASSY, SWIEVE
-9103
037
[01]
LEVER ASSY, SWIEVE
9103-
038
[02]
BUSHING, LEVER
039
[02]
O-RING
ID15.8
040
[02]
WASHER, SNAP
ID15
041
[01]
SPRING, SPEED CONT
042
[01]
SPRING, START
043
[01]
ADAPTER ASSY
043-001
[01]
E-RING
043-002
[01]
SCREW, ADPTER
043-003
[01]
SPRING, MECHANICAL
043-004
[01]
ADAPTER
043-005
[C]
WASHER, PLATE, SK
T0.1
043-005
[C]
WASHER, PLATE, SK
T0.25
043-005
[C]
WASHER, PLATE, SK
T0.5
043-005
[C]
WASHER, PLATE, SK
T0.2
043-005
[C]
WASHER, PLATE, SK
T1.0
044
[01]
NUT, ADAPTER LOCK
045
[04]
BOLT, W/WASHER
M6,L40
046
[02]
BOLT, W/WASHER
M6,L50
047
[01]
SEAL, OIL
050
[01]
LEVER SUB-ASSY, AD
051
[01]
BOLT, W/WASHER
M6,L22
052
[01]
CAP, LEVER
053
[01]
LEVER SUB-ASSY, ST
056
[01]
PLATE, COVER
057
[02]
BOLT, W/WASHER
M6,L14
058
[03]
BOLT, W/WASHER
M6,L14
059
[01]
PLUG, SCREW
060
[02]
WASHER, AIR BLEEDE
T1.6
061
[01]
NUT, CAP
062
[01]
WASHER, COPPER PLA
T1.5
063
[01]
PACKING, RUBBER PL
064
[01]
SPRING, B
OD3.6
065
[01]
O-RING
ID9.0
066
[01]
BUSHING, BEARING
-9707
066
[01]
BUSHING, BEARING
9707-
067
[01]
COVER, SPRING
068
[01]
SPRING, B
OD6.6
069
[01]
SHAFT, MECHANICAL
070
[01]
CUP, SPRING
071
[01]
LEVER, SUPPORT
072
[01]
SPRING, RETURN
073
[01]
PLATE, CAP
074
[01]
SPRING, B
OD8.6
075
[01]
KEY, WOODRUFF
076
[01]
GASKET
-9408
076
[01]
GASKET
9409-
077
[01]
GASKET
-9309
077
[01]
GASKET
9310-
078
[01]
LEVER SUB-ASSY
079
[01]
PIN, TORQUE CONTRO
080
[01]
WASHER, PLATE
T0.5
081
[01]
E-RING
082
[01]
ADAPTER ASSY
082-001
[01]
SCREW, ADJUSTING
082-002
[01]
ADAPTER
082-003
[01]
SPRING, MECHANICAL
082-004
[01]
RING, HOLE SNAP
OD12
082-005
[C]
WASHER, PLATE, SK
T0.1
082-005
[C]
WASHER, PLATE, SK
T0.25
082-005
[C]
WASHER, PLATE, SK
T0.5
082-005
[C]
WASHER, PLATE, SK
T0.2
082-005
[C]
WASHER, PLATE, SK
T1.0
083
[01]
CAP
084
[01]
NUT, HEXAGON, W/HO
085
[02]
WASHER, COPPER PLA
T1,FOR M16
088
[01]
NUT, HEXAGON
M8 -9503
088
[01]
NUT, HEXAGON
M8 9504-
089
[02]
WASHER, COPPER PLA
T1
090
[01]
O-RING
ID12.3

Include in ##:

19080-00900 as GOVERNOR ASSY, MEC

Cross reference number



Part num
Firm num
Firm
Name
19080-00900 
 
GOVERNOR ASSY, MEC




Information:

Start By:a. disassemble governorb. remove fuel injection pumps 1. Remove rack (1) from the fuel pump housing. 2. Remove six lifters (2) from the fuel pump housing. Put identification marks on the lifters for installation purposes. 3. Remove camshaft (3) from the fuel pump housing. It may be necessary to use a soft hammer to push the camshaft out of the governor end of the fuel pump housing. 4. Remove races (4) and bearing (5) from the camshaft. Remove ring (6) if necessary. 5. Remove rack bearing (7) from both ends of the housing and dowel (8) if necessary. 6. Use tooling (A), and remove three camshaft bearings (9). 7. Remove the bolts, cover (10) and the gasket. 8. Remove pins (12), the seal and dowels (11) if necessary. Pins (12) must be pushed from the inside out.Assemble Fuel Injection Pump Housing
1. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. 2. Lubricate the seal with clean engine oil, and install pin (12). Pin (12) must protrude into the pump bore 2.15 .05 mm (.085 .002 in.).3. Install dowel (11) so that it protrudes into the pump bore 1.93 0.05 mm (.076 .002 in.). 4. Install the gasket, cover (10) and the bolts. 5. Install the rack bearing with tooling (B). Install the bearing until the driver comes in contact with the plate. The bearing should be installed to a depth of 83.0 0.5 mm (3.27 .02 in.) from the fuel pump mounting face. 6. Measure rack bearing (7). Dimension (X) must be 11.178 0.05 mm (.4400 .002 in.). Diameter (W) must be 12.767 0.058 mm (.5026 .0022 in.). 7. Install dowel (8). Dowel (8) must protrude 6.0 0.5 mm (.24 .02 in.) from the fuel pump housing face.8. Install the rear rack bearing with tooling (C) to a depth of 7.16 0.13 mm (.282 .005 in.) below the fuel pump housing surface. The inside diameter of the rear rack bearing must be 12.746 0.045 mm (.5018 .0017 in.). 9. Use tooling (D), and install three camshaft bearings (9). Oil holes (13) in the camshaft bearings must be positioned 30° 3° above the horizontal centerline toward the engine side of the fuel pump housing. The outer bearings must be installed 1.0 0.5 mm (0.04 0.02 in.) below the surface marked (Z). The inner bearing must be installed 218.0 0.3 mm (8.58 .012 in.) below the front surface (Y). Diameter (XX) must be 68.339 0.038 mm (2.6905 .0015 in.) after assembly. 10. Install ring (6) races (4) and bearing (5) on the camshaft. 11. Lubricate cam bearings (9) and the camshaft bearing journals with clean engine oil.12. Install camshaft (3) into the fuel pump housing.
The notch in the lifter must be in line with the dowel in the lifter bore. The lifter must slide up and down freely in

Have questions with 19080-00900?





Group cross 19080-00900

Back to top