09080-09691 GOVERNOR ASSY, MEC Denso Cross


Rating:
29
Buy GOVERNOR ASSY, MEC 09080-09691 genuine, new aftermarket engine parts with delivery

Information governor assy, mec Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
GOVERNOR ASSY, MEC
RSV -8810
000
[01]
09080-09691
GOVERNOR ASSY, MEC
8810-
001
[01]
HOUSING SUB-ASSY,
002
[01]
PLATE
003
[02]
SCREW, ADJUSTING
004
[01]
COVER, GOVERNOR
005
[01]
JOINT, FORK
006
[01]
PIN, STOP
009
[01]
NUT, CAP
010
[01]
SCREW, STROKE ADJU
011
[01]
BUSHING
012
[01]
LEVER, TENSION
-8601
012
[01]
LEVER, TENSION
8601--9404
012
[01]
LEVER, TENSION
9404-
015
[01]
LEVER ASSY, CONTRO
L/R:1.2
016
[01]
SHAFT, LEVER SUPPO
017
[02]
PLUG, SCREW
019
[01]
E-RING
021
[02]
NUT, HEXAGON, W/HO
022
[01]
SLIDER, SUPPORTING
023
[01]
CAPSULE, FULL STOP
025
[01]
NUT, ADAPTER LOCK
026
[01]
SHACKLE ASSY
030
[01]
KEY, WOODRUFF
031
[01]
FLYWEIGHT ASSY
032
[01]
WASHER, SPRING
T2.5
033
[01]
NUT, ROUND
034
[01]
SLEEVE SUB-ASSY, F
034-001
[01]
PLATE, THRUST
034-002
[01]
RING, HOLE SNAP
035
[4C]
WASHER, PLATE, SK
T0.2
035
[4C]
WASHER, PLATE, SK
T0.3
035
[4C]
WASHER, PLATE, SK
T0.4
035
[4C]
WASHER, PLATE, SK
T0.1
035
[4C]
WASHER, PLATE, SK
T1.0
037
[01]
LEVER ASSY, SWIEVE
038
[02]
BUSHING, LEVER
-9212
038
[02]
BUSHING, LEVER
9212-
039
[02]
O-RING
-8708
039
[02]
O-RING
8708-
040
[02]
WASHER, SNAP
ID15
041
[01]
SPRING, SPEED CONT
042
[01]
SPRING, START
043
[01]
ADAPTER ASSY
043-001
[01]
SCREW, ADPTER
043-002
[01]
ADAPTER
043-003
[01]
SPRING, MECHANICAL
043-004
[01]
SPRING, MECHANICAL
043-005
[1C]
WASHER, PLATE, SK
T0.1
043-005
[1C]
WASHER, PLATE, SK
T0.2
043-006
[1C]
WASHER, PLATE, SK
T0.3
043-006
[1C]
WASHER, PLATE, SK
T0.1
044
[01]
NUT, ADAPTER LOCK
045
[04]
BOLT, W/WASHER
M6,L40
046
[02]
BOLT, W/WASHER
M6,L50
047
[01]
SEAL, OIL
-8810
047
[01]
SEAL, OIL
8810-
049
[01]
LEVER, ADJUSTING
050
[01]
LEVER SUB-ASSY, AD
-9209
050
[01]
LEVER SUB-ASSY, AD
9209-
051
[01]
BOLT, W/WASHER
M6,L22
052
[01]
CAP, LEVER
054
[02]
BOLT, W/WASHER
M6,L14
056
[01]
PLATE, COVER
057
[02]
BOLT, W/WASHER
M6,L14
058
[02]
BOLT, W/WASHER
M6,L16
059
[01]
SCREW,PLUG
060
[02]
WASHER, AIR BLEEDE
T1.6
061
[01]
NUT, CAP
063
[01]
PACKING, RUBBER PL
-8807
063
[01]
PACKING, RUBBER PL
8807-
075
[01]
KEY, WOODRUFF
076
[01]
GASKET, PUMP BODY
-9304
076
[01]
GASKET, PUMP BODY
9305-
077
[01]
GASKET
-9305
077
[01]
GASKET
9306-
086
[01]
BUSHING
8708-
087
[1C]
WASHER, PLATE, SK
T0.3 8708-
087
[1C]
WASHER, PLATE, SK
T0.6 8708-
087
[1C]
WASHER, PLATE, SK
T0.9 8708-
088
[01]
NUT, HEXAGON
M8 -9503
088
[01]
NUT, HEXAGON
M8 9504-
089
[02]
WASHER, COPPER PLA
T1
090
[01]
O-RING
-8807
090
[01]
O-RING
8807-
091
[01]
SCREW, HOLLOW
092
[02]
WASHER, FUEL PIPE

Include in ##:

09080-09691 as GOVERNOR ASSY, MEC

Cross reference number



Part num
Firm num
Firm
Name
09080-09691 
 
GOVERNOR ASSY, MEC




Information:

2. Turn the crankshaft until two pistons are at bottom center.3. Remove bolts (1) and the bearing caps. Push the rods and pistons up until the rings are out of the cylinder liners. 4. Remove pistons (2) and connecting rods from the cylinder liners.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.Install Pistons & Connecting Rod Assemblies
1. Put clean engine oil on piston rings, connecting rod bearings and cylinder liners. 2. Use Tool (A), and install piston (2) and the connecting rod in the cylinder liner.3. Install the bearing cap on the connecting rod with the number on the side of the bearing cap on the same side and same number as on the connecting rod.4. Put 2P2506 Thread Lubricant on the threads of the bolts. Install the nuts, and tighten them to a torque of 90 8 N m (67 6 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 90 5 degrees.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.End By:a. install piston cooling tubesb. install oil pumpc. install cylinder head assemblyDisassemble & Assemble Pistons & Connecting Rod Assemblies
Start By:a. remove pistons and connecting rod assemblies 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with Tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove piston rings (5) from the piston with Tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See, Use Of Piston Bearing Removal And Installation Tools, Special Instructions, SMHS7295.5. Heat connecting rod (4) in an oven to a temperature of 177° to 260°C (350° to 500° F). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of Tool (C). Put a new rod pin bearing (6) on the adapter part of Tool (C). The old bearing is pushed out by Tool (C) as the new bearing is installed.7. Use Tool (C) to push the new bearing into the connecting rod until the push adapter of Tool (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 50.830 0.008 mm (2.0012 .0003 in).9. Check the clearance between the ends of the piston rings. See the topic, "Pistons & Rings" in Specifications Manual, SENR6470.10. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring joint.11. Install the oil ring on the piston with tool (B).12. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston. Use Tool (B) to install

Have questions with 09080-09691?





Group cross 09080-09691

Back to top