09080-00882 GOVERNOR ASSY, MEC Denso Cross


Rating:
65
Buy GOVERNOR ASSY, MEC 09080-00882 genuine, new aftermarket engine parts with delivery

Information governor assy, mec Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09080-00882
GOVERNOR ASSY, MEC
RSV
001
[01]
CAP
002
[02]
WASHER, AIR BLEEDE
T1.6
003
[01]
HOUSING, GOVERNOR
004
[01]
STOPPER
005
[01]
GASKET
006
[01]
FLYWEIGHT ASSY
007
[01]
NUT, ROUND
008
[01]
SLEEVE, GOVERNOR
009
[01]
LEVER ASSY, SWIEVE
010
[01]
BUSHING, LEVER
011
[01]
BUSHING, LEVER
012
[01]
E-RING
013
[01]
E-RING
014
[01]
LEVER, TENSION
015
[01]
ADAPTER ASSY
016
[01]
SCREW, ADPTER
017
[01]
SPRING, MECHANICAL
018
[01]
SPRING, MECHANICAL
019
[01]
ADAPTER
020
[02]
WASHER, PLATE, SK
T0.3
021
[2C]
WASHER, PLATE, SK
T0.1
022
[2C]
WASHER, PLATE, SK
T0.2
023
[01]
WASHER, PLATE, SK
T0.1
024
[01]
ADAPTER
025
[01]
NUT, ADAPTER LOCK
026
[01]
LEVER SUB-ASSY, CO
027
[01]
BUSHING
028
[01]
LEVER ASSY, GUIDE
029
[01]
PIN
030
[01]
SHACKLE ASSY
031
[01]
SHAFT, LEVER SUPPO
032
[02]
PLUG, SCREW
033
[01]
SPRING, SPEED CONT
034
[01]
SPRING, START
035
[01]
SCREW, STROKE ADJU
036
[01]
E-RING
037
[01]
COVER, GOVERNOR
038
[01]
PIN, TORQUE CONTRO
039
[01]
SCREW, ADJUSTING
040
[01]
SPRING, IDLING
041
[01]
NUT, CAP
042
[01]
NUT, CAP
043
[01]
PLATE SUB-ASSY, CO
044
[01]
PLATE, COVER
045
[02]
O-RING
046
[01]
LEVER SUB-ASSY, AD
047
[01]
CAP, LEVER
048
[01]
PLUG, SCREW
049
[06]
WASHER, SPRING
FOR M6
050
[02]
PIN, SPLIT
D2,L10
051
[02]
BOLT, W/WASHER
M6,L20
052
[02]
NUT, HEXAGON, W/HO
M8
053
[01]
NUT, HEXAGON, W/HO
054
[03]
WASHER, PLATE, SK
T0.3
054
[4C]
WASHER, PLATE, SK
T0.2
054
[4C]
WASHER, PLATE, SK
T0.3
054
[4C]
WASHER, PLATE, SK
T0.4
054
[4C]
WASHER, PLATE, SK
T0.1
054
[4C]
WASHER, PLATE, SK
T1.0
060
[01]
WASHER, SPRING
T2.5
061
[02]
WASHER, COPPER PLA
T1,FOR M16
062
[01]
WASHER, COPPER PLA
T1
063
[06]
BOLT, HEXAGON
M6,L50
064
[01]
BOLT, W/WASHER
M6,L22
065
[02]
BOLT, W/WASHER
M6,L18
066
[01]
NUT, HEXAGON
M8
067
[01]
NUT, HEXAGON
M12
068
[02]
WASHER, SNAP
ID15
069
[01]
BEARING, BALL
OD30
070
[01]
KEY, WOODRUFF
071
[01]
KEY, WOODRUFF
072
[02]
O-RING
ID17.6
073
[01]
SEAL, OIL
074
[01]
SEAL, OIL

Include in ##:

09000-07580 as GOVERNOR ASSY, MEC
09080-00882 GOVERNOR ASSY, MEC

Cross reference number



Part num
Firm num
Firm
Name
09080-00882 
 
GOVERNOR ASSY, MEC




Information:

1. Remove the fuel injection nozzle assembly, and put the piston on TDC (top dead center) for the respective cylinder for which the valve stem seal and O-ring seals are to be removed.2. Install air chuck adapter (2). Fasten a pressure air source to pressurize the cylinder.3. Use tooling (A) to compress the valve springs. Use magnet bar (1) to hold the keepers.4. Remove tool (A), and remove the valve springs and retainer. 5. Remove exhaust valve O-ring seal (3) and inlet valve guide seal (4).
Do not release air pressure in the cylinder until the valve springs and retainer have been installed. Failure to do so will let the valve fall into the top of the piston. If the piston is not at TDC (top dead center) the valve can fall into the cylinder making cylinder head removal necessary.
Install Valve Guide Seals
1. Install spring seating washer (1). 2. Put clean engine oil on the part of valve guide seal (2) that makes contact with the valve stem. Install valve guide seal (2).
The closed coil of the spring must be toward the cylinder rod.
3. Put inner and outer springs (4) and retainer (3) in position.
The locks can be thrown from the valve when the compressor is released if they are not in their correct position on the valve stem.
4. Use tool (A) to compress the valve springs so the keepers can be installed.5. Use tool (B) to install the keepers.6. Repeat Steps 1-4 for O-ring seals (5) on the exhaust valve.7. Move the piston off T.D.C. (top dead center) and tap the valve spring retainer with a soft hammer to be sure the retainers are properly seated.8. Install the fuel injection nozzle assembly.End By:a. install rocker shaft and push rods

Have questions with 09080-00882?





Group cross 09080-00882

Back to top