19260-00901 COMPENSATOR SUB-AS Denso Cross


Rating:
4
Buy COMPENSATOR SUB-AS 19260-00901 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19260-00901
COMPENSATOR SUB-AS
22340-1220 HINO
000
[01]
19260-00901
COMPENSATOR SUB-AS
S2234-01220 HINO
001
[01]
HOUSING, BOOST COM
22431-1020A HINO
002
[01]
COVER SUB-ASSY
22435-1020A HINO
003
[01]
WASHER, THRUST
22434-1030A HINO
004
[01]
SEAT, SPRING, UPR
22434-1020A HINO
005
[01]
ROD, PUSH
22432-1040A HINO
006
[01]
BUSHING, GUIDE
22375-1150A HINO
007
[01]
NUT, HEXAGON
M6,L5
22825-1480A HINO
008
[01]
SCREW
22432-1030A HINO
009
[01]
SPRING, BOOST COMP
22433-1620A HINO
010
[01]
DIAPHRAGM
22361-1050A HINO
011
[01]
NUT, HEXAGON
M6,L36
92100-6040A HINO
012
[01]
WASHER, WAVE
T0.5
22323-1180A HINO
013
[02]
WASHER, COPPER PLA
T1,ID8.2
22847-1300A HINO
014
[01]
NUT, CAP
L18 -9707
22342-1300A HINO
014
[01]
NUT, CAP
9707-
22342-1301A HINO
015
[01]
SCREW, STOP
L33 -9707
22865-1490A HINO
015
[01]
SCREW, STOP
9707-
22865-1520A HINO
016
[01]
NUT, HEXAGON, W/HO
-9707
22825-1060A HINO
016
[01]
NUT
9707-
22825-1061A HINO
019
[01]
PLUG, SCREW
22845-1300A HINO
020
[01]
WASHER, COPPER PLA
T1.5
22867-1170A HINO
021
[03]
BOLT, HEXAGON
M6,L12
22815-2040A HINO
022
[01]
BOLT, HEXAGON, W/
M6,L12
22815-2050A HINO

Cross reference number



Part num
Firm num
Firm
Name
19260-00901 
22340-1220 
COMPENSATOR SUB-AS




Information:


Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Put compression on valve spring (2) with tool (A), and remove locks (1).2. Remove tool (A), rotocoil, spring, valve stem oil shield and valve. Put identification marks on valves with respect to their location in the cylinder head. 3. Check the spring force with tool (B). The spring force is 257 25 N (57.8 5.6 lb.). The length of spring under test force is 44.86 mm (1.766 in). The free length after test is 52.07 mm (2.050 in).4. Perform Steps 1 through 3 again for the remainder of the valves. The following steps are for the installation of the valves.5. Put clean engine oil on the valve stems. Install the valve, oil shield, spring (2) and rotocoil in the cylinder head. 6. Put tool (A) in position on the valve spring, and install the locks with tool (C).
Locks can be thrown from valve when the compressor is released if they are not in their correct position on valve stem. Personal injury can be the result if not carefully removed.
7. Remove tool (A), and hit the top of valve with a plastic hammer be sure the locks are in their correct position on valve.8. Do Steps 5 through 7 again for the remainder of the valves.End By:a. install spacer plate

Have questions with 19260-00901?





Group cross 19260-00901

Back to top