19260-00591 COMPENSATOR SUB-AS Denso Cross


Rating:
17
Buy COMPENSATOR SUB-AS 19260-00591 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
19260-00591
COMPENSATOR SUB-AS
001
[01]
HOUSING, BOOST COM
22431-1020A HINO
002
[01]
COVER SUB-ASSY
22435-1020A HINO
003
[01]
WASHER, THRUST
22434-1030A HINO
004
[01]
SEAT, SPRING, UPR
22434-1020A HINO
005
[01]
ROD, PUSH
22432-1040A HINO
006
[01]
BUSHING, GUIDE
22375-1150A HINO
007
[01]
NUT, HEXAGON
22825-1480A HINO
008
[01]
SCREW
22432-1030A HINO
009
[01]
SPRING, BOOST COMP
010
[01]
DIAPHRAGM
22361-1050A HINO
011
[01]
NUT, HEXAGON
92100-6040A HINO
012
[01]
WASHER, WAVE
T0.5
22323-1180A HINO
013
[02]
WASHER, COPPER PLA
T1
22867-1500A HINO
014
[01]
NUT, CAP
22342-1300A HINO
015
[01]
SCREW, STOP
016
[01]
NUT, HEXAGON, W/HO
22825-1060A HINO
019
[01]
PLUG, SCREW
22845-1300A HINO
020
[01]
WASHER, COPPER PLA
T1.5
22843-1430A HINO
021
[01]
BOLT, HEXAGON
22815-2040A HINO
022
[01]
BOLT, HEXAGON, W/
M6,L12
22815-2050A HINO

Include in ##:

09130-04340 as COMPENSATOR SUB-AS
19260-00591 COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
19260-00591 
22430-1550 
COMPENSATOR SUB-AS




Information:

1. Bend the tabs of the locks from bolts (2) and remove bolts (2) and sleeve (1).2. Remove five bolts (3) from the flywheel housing. 3. Remove the two bolts and remove tachometer drive (8) from flywheel housing (7).4. Remove the five bolts that hold the flywheel housing to the timing gear plate on the left side of the engine.5. Remove two bolts (5), the three bolts (6) and bolt (9).6. Remove the two bolts that hold the flywheel housing to the timing gear plate at the accessory drive on the right side of the engine.7. Remove nuts (4), and use two persons to remove flywheel housing (7). The weight of the flywheel housing is 90 lb. (41 kg).Install Flywheel Housing
1. Clean the surface of the timing gear plate and put the flywheel housing gasket in position. 2. Put flywheel housing (1) in position and install the nuts and bolts to hold it. 3. Tighten two bolts (3) to a torque of 40 5 lb. ft. (55 7 N m). Tighten three bolts (2) to a torque of 95 10 lb. ft. (130 14 N m). 4. Put the O-ring seal (4) on tachometer drive and install the tachometer drive. Make sure tachometer drive is correctly engaged with the drive shaft before the bolts that hold it are tightened. 5. Install sleeve (5) evenly on the crankshaft rear seal and install the bolts and locks to hold it.end by: a) install BrakeSaverb) install BrakeSaver control valvec) install electric starting motord) install air compressore) install oil pan

Have questions with 19260-00591?





Group cross 19260-00591

Back to top