09649-01080 COMPENSATOR SUB-AS Denso Cross


Rating:
53
Buy COMPENSATOR SUB-AS 09649-01080 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09649-01080
COMPENSATOR SUB-AS
001
[01]
COVER SUB-ASSY, GO
002
[01]
COVER SUB-ASSY, GO
003
[01]
STOPPER, TIMER SLI
ME736268 MITSUBISHI
004
[01]
R0D, PUSH
ME736269 MITSUBISHI
005
[01]
BUSHING, GUIDE
ME736270 MITSUBISHI
006
[01]
DIAPHRAGM
ME736271 MITSUBISHI
007
[01]
SHEET, PLUNGER SPR
ME736272 MITSUBISHI
008
[01]
BUSHING, GUIDE
ME736273 MITSUBISHI
009
[01]
NUT, HEXAGON
M18
ME736274 MITSUBISHI
010
[01]
CLIP, TIMER
ME736275 MITSUBISHI
011
[01]
PIN, LEVER CONECTI
ME736276 MITSUBISHI
012
[01]
BUSHING, GUIDE
ME736277 MITSUBISHI
013
[01]
NUT, GOVERNOR SHAF
ME736278 MITSUBISHI
014
[01]
WASHER, COPPER PLA
T1
ME736279 MITSUBISHI
015
[01]
O-RING
ID 4
ME736280 MITSUBISHI
016
[01]
PIN, LEVER SUPPORT
ME736281 MITSUBISHI
017
[01]
LEVER SUB-ASSY, CO
-9805
ME736482 MITSUBISHI
017
[01]
LEVER SUB-ASSY, CO
9806-
018
[02]
GASKET, DELIVERY V
019
[04]
BOLT, SOCKET
M6,L14
ME736283 MITSUBISHI
020
[02]
BOLT, GOVERNOR LIN
ME736284 MITSUBISHI
021
[01]
O-RING
ID10
ME736285 MITSUBISHI
022
[01]
NUT, HEXAGON
M8 -0602
ME736286 MITSUBISHI
022
[01]
NUT, HEXAGON
M8 0602-
023
[01]
WASHER, PLATE
T1
ME736287 MITSUBISHI
024
[01]
NUT, HEXAGON
ME736288 MITSUBISHI
025
[01]
SCREW SUB-ASSY, OV
026
[01]
WASHER, AIR BLEEDE
T1.6
ME702102 MITSUBISHI
027
[01]
PLUG, SCREW
ME703104 MITSUBISHI
028
[1C]
SPRING, BOOST COMP
L20.3
028
[1C]
SPRING, BOOST COMP
L19.7
028
[1C]
SPRING, BOOST COMP
L21.0
029
[1C]
SHIM, BOOST COMPEN
T1.9
ME736305 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T2.1
ME736306 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T2.3
ME736307 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T2.5
ME736292 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T2.7
ME736293 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T2.9
ME736294 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T3.1
ME736295 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T3.3
ME736296 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T1.1
ME736297 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T1.3
ME736298 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T1.5
ME736299 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T1.7
ME736300 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T0.3
ME736301 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T0.5
ME736302 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T0.7
ME736303 MITSUBISHI
029
[1C]
SHIM, BOOST COMPEN
T0.9
ME736304 MITSUBISHI
030
[01]
WASHER, THRUST
ME736308 MITSUBISHI

Include in ##:

09600-08093 as COMPENSATOR SUB-AS
09649-01080 COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
09649-01080 
 
COMPENSATOR SUB-AS




Information:

Altitude Operation
The fuel system settings and altitude limits are stamped on the engine information plate. When an engine is moved to a higher altitude, these settings must be changed by your Caterpillar dealer in order to prevent damaging the turbocharger, and to provide maximum engine efficiency. If the engine is moved to a lower altitude than that which is stamped on the engine information plate, the engine can be operated safely; however, it will deliver less than rated horsepower, and the fuel settings should be changed by your Caterpillar dealer to obtain rated horsepower.Stopping
1. Flywheel clutch operation: Quickly pull the clutch lever to the released position. For electric set operation, see the GENERATOR SET OPERATION instructions. For Woodward Governor operation, see the topic, WOODWARD GOVERNORS, Stopping the Engine. 2. Reduce engine speed to half speed. Run for 5 minutes to cool engine.3. Reduce engine speed to low idle.4. Observe the crankcase oil level while the engine is idling. Maintain the oil level between the ADD and FULL marks on the side of the dipstick stamped, CHECK WITH ENGINE RUNNING. See the LUBRICATION AND MAINTENANCE SECTION.5. Stop the engine. After Stopping Checks And Procedures
1. Fill the fuel tank. See the LUBRICATION AND MAINTENANCE SECTION: Fuel Tank Maintenance.2. Drain the raw water system if below freezing temperatures are expected; see: Draining Raw Water System.3. If below freezing temperatures are expected, allow the engine jacket water expansion tank to cool; then check the coolant for proper antifreeze protection. Add permanent-type antifreeze, if required.4. Repair any leaks, make major adjustments, tighten loose bolts, etc.5. Observe the Service Meter reading. Perform the periodic maintenance as instructed in the LUBRICATION AND MAINTENANCE CHART.
SERVICE METER

Have questions with 09649-01080?





Group cross 09649-01080

Back to top