09649-00492 COMPENSATOR SUB-AS Denso Cross


Rating:
17
Buy COMPENSATOR SUB-AS 09649-00492 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09649-00492
COMPENSATOR SUB-AS
001
[01]
COVER SUB-ASSY, GO
002
[01]
COVER SUB-ASSY, GO
003
[01]
STOPPER, TIMER SLI
004
[01]
R0D, PUSH
005
[01]
BUSHING, GUIDE
006
[01]
DIAPHRAGM
007
[01]
SHEET, PLUNGER SPR
008
[01]
BUSHING, GUIDE
009
[01]
NUT, HEXAGON
M18
010
[01]
CLIP, TIMER
011
[01]
PIN, LEVER CONECTI
012
[01]
BUSHING, GUIDE
013
[01]
NUT, GOVERNOR SHAF
014
[01]
WASHER, COPPER PLA
T1
015
[01]
O-RING
ID 4
016
[01]
PIN, LEVER SUPPORT
017
[01]
LEVER SUB-ASSY, CO
-9805
017
[01]
LEVER SUB-ASSY, CO
9806-
018
[02]
WASHER, DRAIN SCRE
-9407
018
[02]
GASKET, DELIVERY V
9407-
019
[04]
BOLT, SOCKET
M6,L14
020
[02]
BOLT, GOVERNOR LIN
021
[01]
O-RING
ID10
022
[01]
NUT, HEXAGON
M10
023
[01]
WASHER, PLATE
T1
024
[01]
NUT, HEXAGON
M6,L3.6 -9204
024
[01]
NUT, HEXAGON
9204-
026
[02]
WASHER, AIR BLEEDE
T1.6 -9703
026
[02]
GASKET, DELIVERY V
9704-
027
[01]
PLUG, SCREW
028
[1C]
SPRING, BOOST COMP
L19.5
028
[1C]
SPRING, BOOST COMP
L21.0
029
[1C]
SHIM, BOOST COMPEN
T1.9 -9103
029
[1C]
SHIM, BOOST COMPEN
T2.1 -9103
029
[1C]
SHIM, BOOST COMPEN
T2.3 -9103
029
[1C]
SHIM, BOOST COMPEN
T1.1 -9103
029
[1C]
SHIM, BOOST COMPEN
T1.3 -9103
029
[1C]
SHIM, BOOST COMPEN
T1.5 -9103
029
[1C]
SHIM, BOOST COMPEN
T1.7 -9103
029
[1C]
SHIM, BOOST COMPEN
T0.3 -9103
029
[1C]
SHIM, BOOST COMPEN
T0.5 -9103
029
[1C]
SHIM, BOOST COMPEN
T0.7 -9103
029
[1C]
SHIM, BOOST COMPEN
T0.9 -9103
030
[01]
WASHER, THRUST

Include in ##:

09600-04240 as COMPENSATOR SUB-AS
09649-00492 COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
09649-00492 
 
COMPENSATOR SUB-AS




Information:

Introduction
This Special Instruction covers the procedure to install a Flow Through Diesel Particulate Filter on R1300G Load Haul Dump Machines. This supplemental product support literature should be used with the appropriate Service Manual and the appropriate Parts Manual that is available for this standard machine.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Read the entire Special Instruction. Understand the information before you perform any procedures. Understand the information before you order any parts.Note: This procedure cannot be used in Canadian provinces that require "CANMET"certification. This procedure will invalidate the existing "CANMET" approval for an engine.Safety Section
Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive.Ensure that all personnel are safe when using a tool, procedure, work method, or operating technique not recommended by Caterpillar. Ensure that the product will not be damaged or the product made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
Personal injury or death can result from machine articulation or movement. Machine frames can move and a person can be crushed. Connect the steering frame lock between the front and rear frames before working on the machine.Before operating the machine, place the steering frame lock in the stored position.Failure to place the steering frame lock into the stored position before operating can result in loss of steering.
The muffler, catalytic converter/muffler, and diesel particulate filter will become extremely hot during engine operation. A hot muffler, catalytic converter/muffler and diesel particulate filter can cause serious burns. Allow adequate cooling time before working on or near the muffler, catalytic converter/muffler and diesel particulate filter.
Diesel engine exhaust contains products of combustion which may cause personal injury.Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Reference Section
Reference: Disassembly and Assembly, RENR6929, "R1300G Load Haul Dump 3306 Engine Supplement".Required Parts
Table 1
Required Parts
Qty Part Number Description
2 349-8603 (1) Film
2 349-8604 (2) Film
2 350-0684 Film
1 526-3141 Filter GP
(1) ANSI film (USA and Canada)
(2) ISO film (Rest of World)Machine Status - Check
Prior to installing a flow through diesel

Have questions with 09649-00492?





Group cross 09649-00492

Back to top