09649-00461 COMPENSATOR SUB-AS Denso Cross


Rating:
3
Buy COMPENSATOR SUB-AS 09649-00461 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09649-00461
COMPENSATOR SUB-AS
001
[01]
COVER SUB-ASSY, GO
002
[01]
COVER SUB-ASSY, GO
22703-55031 TOYOTA
003
[01]
STOPPER, TIMER SLI
22658-64518 TOYOTA
004
[01]
R0D, PUSH
22321-6A220 TOYOTA
005
[01]
BUSHING, GUIDE
22348-64360 TOYOTA
006
[01]
DIAPHRAGM
22542-54260 TOYOTA
007
[01]
SHEET, PLUNGER SPR
22143-54260 TOYOTA
008
[01]
BUSHING, GUIDE
22348-54490 TOYOTA
009
[01]
NUT, HEXAGON
M18
90099-05156 TOYOTA
010
[01]
CLIP, TIMER
22656-54490 TOYOTA
011
[01]
PIN, LEVER CONECTI
22338-54120 TOYOTA
012
[01]
BUSHING, GUIDE
22348-54121 TOYOTA
013
[01]
NUT, GOVERNOR SHAF
22722-54120 TOYOTA
014
[01]
WASHER, COPPER PLA
T1
90099-01473 TOYOTA
015
[01]
O-RING
ID 4
22193-55031 TOYOTA
016
[01]
PIN, LEVER SUPPORT
22526-54120 TOYOTA
017
[01]
LEVER SUB-ASSY, CO
-9805
22308-54120 TOYOTA
017
[01]
LEVER SUB-ASSY, CO
9806-
018
[02]
WASHER, DRAIN SCRE
-9408
22378-76010 TOYOTA
018
[02]
GASKET, DELIVERY V
9408-
22149-6D450 TOYOTA
019
[04]
BOLT, SOCKET
M6,L14
22395-54263 TOYOTA
020
[02]
BOLT, GOVERNOR LIN
22739-54120 TOYOTA
021
[01]
O-RING
ID10
22193-54561 TOYOTA
022
[01]
NUT, HEXAGON
M10
90099-05181 TOYOTA
023
[01]
WASHER, PLATE
T1
90093-00802 TOYOTA
024
[01]
NUT, HEXAGON
90092-20608 TOYOTA
025
[01]
SCREW SUB-ASSY, OV
W/FILTER
22160-54262 TOYOTA
026
[01]
WASHER, AIR BLEEDE
-9704
22119-77020 TOYOTA
026
[01]
GASKET, DELIVERY V
9704-
22149-54800 TOYOTA
027
[01]
PLUG, SCREW
22129-54120 TOYOTA
028
[1C]
SPRING, BOOST COMP
L20.3
22546-54490 TOYOTA
028
[1C]
SPRING, BOOST COMP
L19.7
22546-54491 TOYOTA
028
[1C]
SPRING, BOOST COMP
L19.2
22546-54492 TOYOTA
030
[01]
WASHER, THRUST
22549-17140 TOYOTA

Include in ##:

09649-00461 as COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
09649-00461 
 
COMPENSATOR SUB-AS




Information:

Introduction
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.This procedure is used when there is a failure of a fuel injector for a 3500 engine and the fuel injector is being returned to Caterpillar for failure analysis. The information for the injector from the field is incomplete many times, or the information for the injector from the field is not provided. Because of the lack of information, determining the root cause for the failure is much more difficult. "No Fault Found" is determined for the injector. This is frustrating for the customer, for the dealer and for Caterpillar. Following the procedures below and accurately documenting the results will provide the failure analysis group with the information that is needed to determine the root cause for the failure of an injector. This should reduce the amount of injectors that are determined "No Fault Found". A copy of the completed worksheet needs to be included in a separate sealed plastic bag with injectors that are being returned for failure analysis.This worksheet is used in conjunction with the troubleshooting steps that are outlined in the literature for the Caterpillar product that is being serviced. Using the Worksheet
Fill out the initial informationThere are five symptoms. Table 3 provides suggestions for the cause and suggestions in order to fix the problem.For example, a customer indicates that an engine is smoking. Refer to Troubleshooting, "Troubleshooting without a Diagnostic Code". After you refer to the Troubleshooting manual, and you still suspect that the fuel injectors are causing the smoke, follow the suggestions that are listed in Table 3.Initial Information
Table 1
Dealer Name     Date    
Dealer Contact Name     RMA Number    
Contact Phone Number     Engine Serial Number    Symptoms
Table 2
Low Power     High Power     Fuel Dilution     Engine Misfire     Smoke    Worksheet
Table 3
Symptom    Check    Reference Information    Results    
Low power
High power
Engine misfire
Smoke     Connect the Caterpillar Electronic Technician (ET)
Refer to Troubleshooting
Ensure to perform engine speed/timing sensor calibration     Use the Cat ET help button with the software, if necessary.
Refer to related information about Cat ET within Troubleshooting     Any problems found?
Yes / No
Explain if Yes    
Low power
High power
Engine misfire
Smoke     Additional Cat ET diagnostic tips can be found in the Service Training Tips Newsletter     Refer to "Service Training Tech Tips Newsletter, No. 27" (1)     Any problems found?
Yes / No
Explain if Yes    
Engine misfire     Does the ECM function properly?
(Solenoids are actuated during the injector solenoid test)     Refer to engine Troubleshooting, "Injector Solenoid Test"     Did each injector solenoid audibly "click?"
Yes / No    
Low power
Engine misfire     Check for a sufficient fuel supply, sufficient fuel transfer pump pressure.
Check manifold (if multiple engines use the same fuel tank)     Use a 1U-5450 Monitor Arrangement to check for adequate fuel flow.     Fuel transfer
pump pressure    
Flow
Low power     Inspect the fuel system
Fuel line: leaks, damaged line, galled pressure regulator  

Have questions with 09649-00461?





Group cross 09649-00461

Back to top