09649-00094 COMPENSATOR SUB-AS Denso Cross


Rating:
22
Buy COMPENSATOR SUB-AS 09649-00094 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09649-00094
COMPENSATOR SUB-AS
001
[01]
COVER SUB-ASSY, GO
22703-54490 TOYOTA
002
[01]
COVER SUB-ASSY, GO
22703-54262 TOYOTA
003
[01]
STOPPER, TIMER SLI
22658-64518 TOYOTA
004
[01]
R0D, PUSH
22321-54491 TOYOTA
005
[01]
BUSHING, GUIDE
22348-64360 TOYOTA
006
[01]
DIAPHRAGM
22542-54260 TOYOTA
007
[01]
SHEET, PLUNGER SPR
22143-54260 TOYOTA
008
[01]
BUSHING, GUIDE
22348-54490 TOYOTA
009
[01]
NUT, HEXAGON
M18
90099-05156 TOYOTA
010
[01]
CLIP, TIMER
22656-54490 TOYOTA
011
[01]
PIN, LEVER CONECTI
22338-54120 TOYOTA
012
[01]
BUSHING, GUIDE
22348-54121 TOYOTA
013
[01]
NUT, GOVERNOR SHAF
22722-54120 TOYOTA
014
[01]
WASHER, COPPER PLA
T1
90099-01473 TOYOTA
015
[01]
O-RING
22193-55031 TOYOTA
016
[01]
PIN, LEVER SUPPORT
22526-54120 TOYOTA
017
[01]
LEVER SUB-ASSY, CO
-9805
22308-54140 TOYOTA
017
[01]
LEVER SUB-ASSY, CO
9806-
22308-17570 TOYOTA
018
[02]
WASHER, DRAIN SCRE
-9407
22378-76010 TOYOTA
018
[02]
GASKET, DELIVERY V
9407-
22149-6D450 TOYOTA
019
[04]
BOLT, SOCKET
M6,L14
22395-54263 TOYOTA
020
[02]
BOLT, GOVERNOR LIN
22739-54120 TOYOTA
021
[01]
O-RING
22193-54561 TOYOTA
022
[01]
NUT, HEXAGON
M8 -0602
90099-05181 TOYOTA
022
[01]
NUT, HEXAGON
M8 0602-
90099-05252 TOYOTA
023
[01]
WASHER, PLATE
T1
90093-00802 TOYOTA
024
[01]
NUT, HEXAGON
90092-20608 TOYOTA
026
[01]
WASHER, AIR BLEEDE
T1.6 -9703
22119-77020 TOYOTA
026
[01]
GASKET, DELIVERY V
9704-
22149-54800 TOYOTA
027
[01]
PLUG, SCREW
22129-54120 TOYOTA
028
[1C]
SPRING, BOOST COMP
K2.1
22546-54490 TOYOTA
028
[1C]
SPRING, BOOST COMP
K2.3
22546-54491 TOYOTA
028
[1C]
SPRING, BOOST COMP
K2.5
22546-54492 TOYOTA
030
[01]
WASHER, THRUST
22549-17140 TOYOTA

Include in ##:

09600-02020 as COMPENSATOR SUB-AS
09649-00094 COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
09649-00094 
 
COMPENSATOR SUB-AS




Information:

Fast IdleFast Idle RPM determines the preset Fast Idle engine rpm as controlled using the Fast Idle Enable Switch. Fast Idle operates similar to cruise control, except it governs engine rpm with the vehicle stationary, or at low vehicle speeds.Flash Code (FC)The Caterpillar proprietary code numbers which are flashed out on the diagnostic lamp. Flash ProgrammingA way of programming or updating an ECM with an Electronic Service Tool over the data link instead of replacing components.Fuel Ratio Control (FRC)FRC Fuel Pos. - is a limit based on control of the fuel-air ratio and is used for emissions control purposes. When the ECM senses a higher boost pressure (more air into cylinder), it increases the "FRC Fuel Pos" limit (allows more fuel into cylinder).Fuel PositionAn internal signal within the ECM, from the Electronic Governor to Fuel Injection Control. It is based on Desired RPM, FRC Fuel Position, rated fuel position and engine rpm. Reference "3100 System Overview" in Section 1 of this manual.Full Load Setting (FLS)Number representing fuel system adjustment made at the factory to "fine tune" the fuel system maximum fuel delivery. Correct value for this parameter is stamped on the engine information ratings plate. This parameter must be programmed or a Diagnostic Code 253-02 Check Customer Or System Parameters (56) will be generated.Full Torque Setting (FTS)Similar to Full Load Setting. This parameter must be programmed or a Diagnostic Code 253-02 Check Customer Or System Parameters (56) will be generated.Gear Down ProtectionProgrammable High Gear Limits used to promote driving in higher gears for increased fuel economy.HarnessThe wiring bundle (loom) connecting all components of the Electronic System.Hertz (Hz)Measure of frequency in cycles per second.Hydraulic Electronic Unit Injector (HEUI)The injection pumping is hydraulically actuated, electronically controlled injector combining the pumping, fuel metering and injecting elements in a single unit.Idle RPM LimitProgrammable parameter which indicates the maximum allowable engine rpm when an engine rpm is set using the Cruise Control On/Off switch and SET/RESUME switch.Idle Shutdown TimeProgrammable parameter which indicates time (in minutes) that the engine will idle before shutting down.Idle/PTO Bump RPMProgrammable parameter indicating the amount which the engine RPM will be incremented/decremented when the Accel/Decel switches are briefly toggled.Injection Actuation Pressure Control ValveThis is an electronically controlled dump valve maintaining the high pressure for the high pressure oil manifold. The valve outputs controlled pressure depending on inputs from the ECM. The control valve regulates the high pressure oil to the injectors through the high pressure rail to provide the actuation force to determine the injection pressure for the engine.Injection Actuation Pressure SensorA device used to detect and convert mechanical oil pressure in the high pressure manifold to an electrical signal to the ECM.Inlet Air HeaterThe Inlet Air Heater is used to improve the cold start capability of the engine and to reduce white smoke. The operation is determined at three different times, Power Up/Preheat, Cranking and Engine Started Cycle, based on engine parameters.Intake Manifold Air Temperature SensorThis sensor detects the intake manifold air temperature. The ECM monitors the inlet

Have questions with 09649-00094?





Group cross 09649-00094

Back to top