09649-00071 COMPENSATOR SUB-AS Denso Cross


Rating:
12
Buy COMPENSATOR SUB-AS 09649-00071 genuine, new aftermarket engine parts with delivery

Information compensator sub-as Denso

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09649-00071
COMPENSATOR SUB-AS
001
[01]
COVER SUB-ASSY, GO
002
[01]
COVER SUB-ASSY, GO
003
[01]
STOPPER, TIMER SLI
004
[01]
R0D, PUSH
005
[01]
BUSHING, GUIDE
006
[01]
DIAPHRAGM
007
[01]
SHEET, PLUNGER SPR
008
[01]
BUSHING, GUIDE
009
[01]
NUT, HEXAGON
M18
010
[01]
CLIP, TIMER
011
[01]
PIN, LEVER CONECTI
012
[01]
BUSHING, GUIDE
013
[01]
NUT, GOVERNOR SHAF
014
[01]
WASHER, COPPER PLA
T1
015
[01]
O-RING
ID 4
016
[01]
PIN, LEVER SUPPORT
017
[01]
LEVER SUB-ASSY, CO
-9805
017
[01]
LEVER SUB-ASSY, CO
9806-
018
[02]
WASHER, DRAIN SCRE
-9407
ME702175 MITSUBISHI
018
[02]
GASKET, DELIVERY V
9407-
019
[04]
BOLT, SOCKET
M6,L14
020
[02]
BOLT, GOVERNOR LIN
021
[01]
O-RING
ID10
022
[01]
NUT, HEXAGON
M8 -0602
022
[01]
NUT, HEXAGON
M8 0602-
023
[01]
WASHER, PLATE
T1
024
[01]
NUT, HEXAGON
025
[01]
SCREW, OVERFLOW
026
[02]
WASHER, AIR BLEEDE
T1.6 -9703
ME702102 MITSUBISHI
026
[02]
GASKET, DELIVERY V
9704-
027
[01]
PLUG, SCREW
ME703104 MITSUBISHI
028
[1C]
SPRING, BOOST COMP
K2.0
028
[1C]
SPRING, BOOST COMP
K2.2
028
[1C]
SPRING, BOOST COMP
K2.4
029
[1C]
SHIM, BOOST COMPEN
T1.9
029
[1C]
SHIM, BOOST COMPEN
T2.1
029
[1C]
SHIM, BOOST COMPEN
T2.3
029
[1C]
SHIM, BOOST COMPEN
T2.5
029
[1C]
SHIM, BOOST COMPEN
T2.7
029
[1C]
SHIM, BOOST COMPEN
T2.9
029
[1C]
SHIM, BOOST COMPEN
T3.1
029
[1C]
SHIM, BOOST COMPEN
T3.3
029
[1C]
SHIM, BOOST COMPEN
T1.1
029
[1C]
SHIM, BOOST COMPEN
T1.3
029
[1C]
SHIM, BOOST COMPEN
T1.5
029
[1C]
SHIM, BOOST COMPEN
T1.7
030
[01]
WASHER, THRUST

Include in ##:

09600-01860 as COMPENSATOR SUB-AS
09649-00071 COMPENSATOR SUB-AS

Cross reference number



Part num
Firm num
Firm
Name
09649-00071 
 
COMPENSATOR SUB-AS




Information:


Tightening Procedure For Main Bearings(8) Torque for the bolts that hold the caps for the main bearings: Install the main bearing caps with the marks (arrow) toward the front of the engine. Install each cap in the correct position by putting the number stamped on the bottom of the cap toward the corresponding number cast on left side of the cylinder block at the pan rail.a. Put 2P2506 Thread Lubricant on the threads of the bolts.b. Tighten the bolts first on the bearing tab side of the cap to ... 260 14 N m (190 10 lb ft)c. Tighten the bolts on the opposite side to ... 260 14 N m (190 10 lb ft)d. Put a mark on each bolt and cap.e. Tighten the bolts on the opposite side, from the mark ... 120 5°f. Tighten the bolts on the bearing tab side of the cap, from the mark ... 120 5°(9) Dimension (new) from centerline of crankshaft bearing bore to bottom of block (pan rails) ... 165.10 0.10 mm (6.500 .004 in)
View From Right Side Of Cylinder Block(10) Put 5P3414 Pipe Sealant on threads of plugs before installation in the cylinder block.(11) Torque for bolts holding oil jet cooling tubes ... 30 7 N m (22 5 lb ft) Minimum permissible clearance between piston and oil jet cooling tube ... 0.64 mm (.025 in)

Have questions with 09649-00071?





Group cross 09649-00071

Back to top