Rating:
Information camshaft, supply p Denso
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
94191-9020 Fuel Injection Pump Camshaft Diesel Engine Replacement Part for HP3 294191-0010 294191-0080
xinDieseltt Applicable oil pumps: 294000-0047 294000-0173 || Check whether the part number is correct to avoid installing incorrect parts || Our pump camshaft comes with six-month warranty || Every pump camshaft is rigorously tested and verified || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you
xinDieseltt Applicable oil pumps: 294000-0047 294000-0173 || Check whether the part number is correct to avoid installing incorrect parts || Our pump camshaft comes with six-month warranty || Every pump camshaft is rigorously tested and verified || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you
294191-0010 294191-0080 294000-0019 Fuel Injection Pump Camshaft Diesel Engine Replacement Part for HP3 2KD-FTV 294191-0050 294000-1190
xinDieseltt Applicable oil pumps: 294000-0065 294000-0075 294000-0102 294000-0163 294000-0374 294000-0412 || Check whether the part number is correct to avoid installing incorrect parts || Our pump camshaft comes with six-month warranty || Every pump camshaft is rigorously tested and verified || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you
xinDieseltt Applicable oil pumps: 294000-0065 294000-0075 294000-0102 294000-0163 294000-0374 294000-0412 || Check whether the part number is correct to avoid installing incorrect parts || Our pump camshaft comes with six-month warranty || Every pump camshaft is rigorously tested and verified || If you are unsure if it will fit your vehicle or have problems with installation, please contact our customer service staff to assist you
Include in ##:
29400-00039
as CAMSHAFT, SUPPLY P
Cross reference number
Part num
Firm num
Firm
Name
29419-10080
CAMSHAFT, SUPPLY P
Information:
2. Remove the nuts (1), washers, and bearing caps from the cylinder block.3. Remove the crankshaft from block. Weight of crankshaft is 240 lb. (108 kg).4. Remove the bearings from main bearing caps. 5. Remove the upper halves (2) of bearings from the cylinder block.Install Crankshaft
1. Clean the surfaces for bearings in cylinder block. Install the upper halves of bearings in the block. Put clean oil on the bearings. 2. Fasten a hoist and put the crankshaft in position on block with "V" mark on crankshaft gear in alignment with "V" mark on cluster gear.3. Clean the bearings caps, and install the lower halves of bearings in caps. 4. Use wire (A) to check bearing clearances. Install the bearing caps, and tighten both nuts to 70 5 lb. ft. (9.7 0.7 mkg). Put a mark across the nuts and studs, and turn nuts an additional 90° from mark. Remove caps and check thickness of wire (A) to find bearing clearance. Bearing clearance must be .0030 to .0059 in. (0.07 to 0.14 mm) for new parts. Maximum permissible clearance for used parts is .010 in. (0.254 mm).5. Put clean engine oil on threads of studs, face of washers, and lower halves of bearings. Put the bearing caps in their respective positions with number on cap on same side and the same as number on cylinder block. Install washers and nuts. Tighten nuts to 70 5 lb.ft. (9.7 0.7 mkg). Put a mark across the nuts and studs, and turn nuts an additional 90° from mark as shown. 6. Use indicator group (B) to check the crankshaft end play as controlled by bearing (1) on No. 4 main bearing cap (2). End play with new parts should be .011 to .018 in. (0.28 to 0.46 mm). Maximum permissible end play with used parts is .035 in. (0.89 mm).end by: a) install timing gear housingb) install pistonsc) install front cover
1. Clean the surfaces for bearings in cylinder block. Install the upper halves of bearings in the block. Put clean oil on the bearings. 2. Fasten a hoist and put the crankshaft in position on block with "V" mark on crankshaft gear in alignment with "V" mark on cluster gear.3. Clean the bearings caps, and install the lower halves of bearings in caps. 4. Use wire (A) to check bearing clearances. Install the bearing caps, and tighten both nuts to 70 5 lb. ft. (9.7 0.7 mkg). Put a mark across the nuts and studs, and turn nuts an additional 90° from mark. Remove caps and check thickness of wire (A) to find bearing clearance. Bearing clearance must be .0030 to .0059 in. (0.07 to 0.14 mm) for new parts. Maximum permissible clearance for used parts is .010 in. (0.254 mm).5. Put clean engine oil on threads of studs, face of washers, and lower halves of bearings. Put the bearing caps in their respective positions with number on cap on same side and the same as number on cylinder block. Install washers and nuts. Tighten nuts to 70 5 lb.ft. (9.7 0.7 mkg). Put a mark across the nuts and studs, and turn nuts an additional 90° from mark as shown. 6. Use indicator group (B) to check the crankshaft end play as controlled by bearing (1) on No. 4 main bearing cap (2). End play with new parts should be .011 to .018 in. (0.28 to 0.46 mm). Maximum permissible end play with used parts is .035 in. (0.89 mm).end by: a) install timing gear housingb) install pistonsc) install front cover