09010-08600 BODY ASSY, INJECTI Denso Cross


Rating:
17
Buy BODY ASSY, INJECTI 09010-08600 genuine, new aftermarket engine parts with delivery

Information body assy, injecti Denso

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Body assy, injecti
Body assy, injecti

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09010-08600
BODY ASSY, INJECTI
NE:REINFORCED
001
[01]
HOUSING SUB-ASSY,
001-001
[03]
BOLT, STUD
M6,L26
002
[06]
HOLDER SUB-ASSY, D
003
[06]
O-RING
004
[06]
SPRING, DELIVERY V
006
[06]
VALVE SUB-ASSY, IN
MK:1750
007
[06]
GASKET, DELIVERY V
008
[06]
ELEMENT SUB-ASSY,
011
[06]
COVER, ELEMENT
-9005
011
[06]
COVER, ELEMENT
9005-
012
[06]
RING, SNAP
ID18.2
013
[12]
O-RING
014
[06]
O-RING
-9103
014
[06]
O-RING
9104-
016
[C]
SHIM, ELEMENT HOLD
T1.4
016
[C]
SHIM, ELEMENT HOLD
T1.45
016
[C]
SHIM, ELEMENT HOLD
T1.5
016
[C]
SHIM, ELEMENT HOLD
T1.55
016
[C]
SHIM, ELEMENT HOLD
T1.6
016
[C]
SHIM, ELEMENT HOLD
T0.7
016
[C]
SHIM, ELEMENT HOLD
T0.75
016
[C]
SHIM, ELEMENT HOLD
T0.8
016
[C]
SHIM, ELEMENT HOLD
T0.85
016
[C]
SHIM, ELEMENT HOLD
T0.9
016
[C]
SHIM, ELEMENT HOLD
T0.95
016
[C]
SHIM, ELEMENT HOLD
T1.0
016
[C]
SHIM, ELEMENT HOLD
T1.05
016
[C]
SHIM, ELEMENT HOLD
T1.1
016
[C]
SHIM, ELEMENT HOLD
T1.15
016
[C]
SHIM, ELEMENT HOLD
T1.2
016
[C]
SHIM, ELEMENT HOLD
T1.25
016
[C]
SHIM, ELEMENT HOLD
T1.3
016
[C]
SHIM, ELEMENT HOLD
T1.35
017
[12]
WASHER, STEEL PLAT
018
[12]
WASHER, SPRING
FOR M10
020
[01]
RACK ASSY, CONTROL
020-002
[02]
BOLT
M5,L10
020-004
[02]
WASHER, PLATE, SK
T0.5
021
[02]
BUSHING, CONTROL R
022
[01]
PIN, STRAIGHT
023
[01]
BUSHING, CONTROL R
024
[06]
SLEEVE SUB-ASSY, C
025
[06]
SEAT, SPRING, UPR
026
[06]
SPRING, PUMP PLUNG
027
[06]
SEAT, SPRING, LWR
028
[06]
TAPPET SUB-ASSY,IN
028-001
[06]
ROLLER, INJECTION
028-002
[06]
SLIDER
028-003
[06]
TAPPET, INJECTION
028-004
[06]
PIN, INJECTION PUM
029
[01]
CAMSHAFT, INJECTIO
030
[01]
BEARING, CENTER
032
[02]
SCREW, SLOTTED OVA
M6,L18 -9408
032
[02]
SCREW
M6,L18 9408-
033
[01]
BEARING, ROLLER
034
[01]
COVER, BEARING
035
[01]
SEAL, OIL
036
[01]
O-RING
037
[C]
PLATE, SHIM
T0.03
037
[C]
PLATE, SHIM
T0.05
037
[C]
PLATE, SHIM
T0.07
037
[C]
PLATE, SHIM
T0.1
037
[C]
PLATE, SHIM
T0.2
037
[C]
PLATE, SHIM
T0.3
037
[C]
PLATE, SHIM
T0.5
038
[01]
RETAINER, BEARING
041
[01]
PLUG, SCREW
042
[06]
PLUG, SCREW
043
[01]
PLATE, INJECTION P
044
[12]
SCREW, SLOTTED POL
M6,L12
046
[01]
BEARING, ROLLER
048
[03]
SCREW, HOLLOW
058
[01]
VALVE ASSY, OVERFL
MARK 28
059
[10]
WASHER, FUEL PIPE
061
[02]
BOLT, W/WASHER
M6,L14
063
[01]
O-RING
ID32.0
065
[01]
GASKET, INJECTION
066
[01]
WASHER, COPPER PLA
T2
067
[06]
WASHER, COPPER PLA
T1
070
[01]
NEEDLE, TIMING
071
[C]
WASHER, PLATE, SK
T0.1
071
[C]
WASHER, PLATE, SK
T0.2
071
[C]
WASHER, PLATE, SK
T0.15

Include in ##:

09010-08600 as BODY ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09010-08600 
 
BODY ASSY, INJECTI




Information:

Start By:a. remove oil pumpb. remove oil pan plate
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.
The connecting rod bolts are loose on the connecting rods and can fall out when the nuts are removed.
2. Push the connecting rods away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.3. Install the upper half of the rod bearing in the connecting rod.4. Install the lower half of the rod bearing in the connecting rod cap. Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap. 5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position.
Do not use an impact wrench to tighten the nuts the additional 90°.
8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft). Put a mark on each nut and the end of each bolt. Tighten the nuts 90° more. Remove the connecting rod caps. Remove Plastigage (A) and measure the width of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump

Have questions with 09010-08600?





Group cross 09010-08600

Back to top