09010-07630 BODY ASSY, INJECTI Denso Cross


Rating:
62
Buy BODY ASSY, INJECTI 09010-07630 genuine, new aftermarket engine parts with delivery

Information body assy, injecti Denso

KIT List:

Part name
Kit1
Kit2
Body assy, injecti
Body assy, injecti

Scheme #.#:

Qty
Part num
Name
Remarks
Manufacture num
000
[01]
09010-07630
BODY ASSY, INJECTI
A4
001
[01]
HOUSING KIT, INJEC
001-001
[03]
BOLT, STUD
M6,L26
003
[04]
HOLDER, DELIVERY V
004
[04]
STOPPER, DELIVERY
005
[04]
SPRING, DELIVERY V
006
[04]
GASKET, DELIVERY V
FOR D13
007
[04]
VALVE SUB-ASSY, IN
008
[04]
ELEMENT SUB-ASSY,
MK:3900
009
[04]
PINION, PLUNGER CO
010
[04]
SCREW, PLUNGER CON
011
[04]
SLEEVE, PLUNGER CO
012
[04]
SEAT, SPRING, UPR
-9301
012
[04]
SEAT, SPRING, UPR
9301-
013
[04]
SPRING, PUMP PLUNG
014
[04]
SEAT, SPRING, LWR
015
[04]
TAPPET SUB-ASSY,IN
016
[04]
PLUG, INJECTION PU
017
[01]
CAMSHAFT, INJECTIO
SHAFT D20
018
[01]
RING, CAMSHAFT ADJ
019
[C]
PLATE, CAMSHAFT SH
T0.1
019
[C]
PLATE, CAMSHAFT SH
T0.12
019
[C]
PLATE, CAMSHAFT SH
T0.14
019
[C]
PLATE, CAMSHAFT SH
T0.16
019
[C]
PLATE, CAMSHAFT SH
T0.18
019
[C]
PLATE, CAMSHAFT SH
T0.5
019
[C]
PLATE, CAMSHAFT SH
T0.3
019
[C]
PLATE, CAMSHAFT SH
T0.03 9308-
020
[01]
COVER, BEARING
021
[01]
GASKET, BEARING CO
-9304
021
[01]
GASKET, BEARING CO
9305-
022
[01]
RACK, CONTROL
023
[01]
SCREW, RACK GUIDE
-9308
023
[01]
SCREW, RACK GUIDE
9308-
025
[02]
PLATE SET, VALVE H
026
[04]
O-RING
ID17.0
027
[02]
WASHER, INJECTION
T1,D13.9
028
[01]
COVER SUB-ASSY, IN
-9509
028
[01]
COVER SUB-ASSY, IN
9510-
028-001
[01]
PROCESSING DRAWING
028-002
[01]
GASKET, INJECTION
028-003
[02]
PACKING, AIR BLEED
028-004
[02]
SCREW
029
[C]
PLATE, TAPPET ADJU
T0.6
029
[C]
PLATE, TAPPET ADJU
T0.7
029
[C]
PLATE, TAPPET ADJU
T0.8
029
[C]
PLATE, TAPPET ADJU
T0.9
029
[C]
PLATE, TAPPET ADJU
T1.0
029
[C]
PLATE, TAPPET ADJU
T1.1
029
[C]
PLATE, TAPPET ADJU
T1.2
029
[C]
PLATE, TAPPET ADJU
T1.3
029
[C]
PLATE, TAPPET ADJU
T1.4
029
[C]
PLATE, TAPPET ADJU
T0.1
029
[C]
PLATE, TAPPET ADJU
T0.2
029
[C]
PLATE, TAPPET ADJU
T0.3
029
[C]
PLATE, TAPPET ADJU
T0.4
029
[C]
PLATE, TAPPET ADJU
T0.5
029
[C]
PLATE, TAPPET ADJU
T0.15
030
[03]
NUT, HEXAGON
M6,L5
031
[03]
WASHER, SPRING
T1.5
032
[04]
BOLT, W/WASHER
M6,L20
033
[01]
BEARING, ROLLER
034
[01]
VALVE ASSY, OVERFL
2.4-2.8K
035
[01]
O-RING
ID32.0
036
[01]
SCREW, HOLLOW
M10,L19
037
[01]
SCREW, HOLLOW
M14,L10
043
[01]
BEARING, ROLLER
044
[01]
RING, CAMSHAFT ADJ
045
[04]
WASHER, FUEL PIPE
T1.2
048
[C]
PLATE, CAMSHAFT SH
T0.1
048
[C]
PLATE, CAMSHAFT SH
T0.15
048
[C]
PLATE, CAMSHAFT SH
T0.3
048
[C]
PLATE, CAMSHAFT SH
T0.5
048
[C]
PLATE, CAMSHAFT SH
T0.12
048
[C]
PLATE, CAMSHAFT SH
T0.14
048
[C]
PLATE, CAMSHAFT SH
T0.18
048
[C]
PLATE, CAMSHAFT SH
T0.03 9308-

Include in ##:

09010-07630 as BODY ASSY, INJECTI

Cross reference number



Part num
Firm num
Firm
Name
09010-07630 
 
BODY ASSY, INJECTI




Information:

START BY:a. remove fuel injection pump housing and governorb. remove fuel transfer pumpc. remove tachometer drive If it is desired to only remove the governor so the fuel injection pump housing can be disassembled, do only Steps 1, 2, 3, 16, 22, 25, 26, 27, 28, 32, 34 and 37. 1. Put the fuel injection pump housing and governor in position on tool (A).2. Remove the bolts, fuel ratio control (1) and shutoff solenoid (2) from rear governor housing (3).3. Remove the bolts, rear governor housing (3) and the gasket from the front governor housing. 4. Remove governor spring (4), the two wave washers, one flat washer and the seat from the guide in the rear governor housing. 5. Remove bolt (5) that holds lever assembly (6) to the shaft assembly. There is a key in the (slot) groove of the shaft assembly that must be removed before the shaft assembly is removed from the rear governor housing.6. Remove shaft assembly (7), lever (6) and lever (8) from the rear governor housing. Put an alignment mark on lever (9) for correct assembly purposes.7. Remove bolt (10), lever assembly (9) and spring (11) from shaft assembly (7). 8. Remove plug (12) and lip-type seal (13) from the housing. Spacers (14) and (16) are different sizes. Make sure they are assembled in the correct position.9. Use needle nose pliers, and remove the shaft. Remove spacer (14), lever (15) and spacer (16) from the governor housing. 10. Remove two setscrews and locknuts (17) if necessary. 11. Release spring (18) from the notch in the housing. Remove snap ring (19), and remove shaft (20) from the housing. Remove lever (21) and spring (18). 12. Remove lip-type seal (22) from the housing. 13. If necessary, remove the screws, cover (23) and the gasket from the governor housing. 14. Remove high idle cover (24) and three O-ring seals (25). 15. Remove lip-type seal (26), dashpot valve (27), fitting (25), insulator and high idle adjustment (28) from the rear housing. 16. Remove two bolts (29), housing (30) and the gasket from the fuel pump housing. 17. Remove bolts (31), and remove torque control group (32) from the block.
Depending on the different engine applications, torque control groups will vary. Inspect all parts for wear and damage, and make a note of the correct sequence of the parts for assembly purposes.
For additional information, see Specifications For 3406B Diesel Truck Engines. 18. Remove the bolts and block (33) for the full load stop from the housing. 19. Remove the bolt that holds collar (35) to bolt (36).20. Remove collar (35) and spring (34) from bolt (36). Remove bolt (36) from the block.21. If necessary, remove the stop screw and the power setting screw from collar (35). It may be necessary to turn the piston to remove the servo from the rack.22. Remove the three bolts and governor servo (37) from the fuel injection pump housing. 23. Remove lockring (43), seat (42), spring (41) and sleeve (40) from valve

Have questions with 09010-07630?





Group cross 09010-07630

Back to top